E60: Blocked Washer-Pump - Quick Fix.

No water from windscreen washer-jets? Chances are it's a blockage in the pump filter. This is not a difficult job, rather a very easy one, so avoid unnecessary cost and fix it quickly yourself.

Check Fuse: 
Fuse 18 is the corresponding fuse. If the washer pump is dead and making no noise then this is the first thing to check. If it is still making a whining noise, then you have a blocked pump-filter.

** The headlamp washer system only functions when the headlights / sidelights are turned on. **

FIX:

Windscreen Washer System:

** The washer bottle is located just in front of the N/S (passenger) wheel-arch liner. The filler-neck is just behind the N/S headlamp and you can see the hose go down into the bodywork and rise up to where the tank is. The tank CANNOT be accessed from above, even when the headlamp is removed. It is much easier to peel the arch-liner back and work from inside the wheel-arch. **

** Obviously water will spill out of the washer bottle so just allow it to drain. **

1. Remove the 3 screws from the N/S/F plastic wheel-arch liner circled in the photo so that it can be peeled back out of the arch rim, one on the near edge, one along the bottom and one by the brake air-duct. It helps to turn the wheel full-lock one way or the other to give more room.

2. Gently pull the washer-jet hose connector off the spout on the side of the windscreen washer-pump. [It's the smaller grey one, furthest away in photo].

3. Reach in and grip the windscreen washer-pump, then gently turn it from side to side while lifting it upwards until the spout on the pump is free of the tank [it may need tilting towards the wheel to get out].

4. Unplug the wire-connector from the pump by depressing the clip on either side and sliding it upwards. The pump can now be removed from inspection if necessary. [Alternatively, leave the wiring connected and place the pump somewhere out of the way].

5. Gently prise the rubber base the pump sits in upwards out of it's collar in the tank, being careful not to detach the plastic-filter from below it and have it drop into the tank.

6. Remove the white plastic filter from the rubber piece and give it a good clean. [It's usually congealed screen-wash clogging it as in the photo, rather than detritus].

7. Refit the plastic filter to the bottom of the rubber base and carefully lower it vertically back into the tank.

8. Refit the pump as a reversal of steps 4 to 1.

Sticky residue wrapped right around the filter-gauze
had stopped flow into the pump completely.

Headlamp Washer System:
The process is the same for the larger headlamp washer pump, though the hose-connector at the bottom in the second photo is sturdier and needs the clip pushing up from undernath to slide the hose off.

Headlamp washer has a much bigger filter, I guess to get more
water into the bigger pump and higher pressure spray.

E21 316: Re-Spray Strip-Down 3 - Wipers + Washer Nozzle Removal.

A. Washer-Jet Nozzles:

1. Twist and pull the hose off from below the washer-nozzles.

2. The nozzles have a plastic at the base that spreads when they're pushed into the body, so working them out is pretty easy by pressing the flaps in with your finger one at a time.

B. Windscreen Wiper-Arms + Bases:

1. Lift the cap at each wiper-arm base and, using an adjustable-spanner, remove the top-nut and washer.

2. Raise the wiper-arm to an upright position and wiggle it off the spline.

3. Remove the large diameter nut and washer from the base-mount and remove the mount. *The rubber seal will likely be perished and hard to find a replacement, but you can just cut a new one out of sheet-rubber as I did, or I will supply a set for £1.99 inc. postage to mainland UK - see here.

E39: Replacing / Unclogging the Washer-Jet Pump

If you think your pump is faulty then check this post first - Windscreen Washer-Jet System Problem.

-----------------------------------------

Removing the pump is easy, but getting to it is quite involved due to the amount of under-car panelling the E39 has.

PROCESS:

1. Jack up the o/s front of the car and detach the plastic mud-guard by removing the 3 hex-head screws that hold it to the wheel-arch. using a 7mm wrench.

2. Lift off the plastic under-tray that sits to the rear of the wheel-arch by removing the 5 plastic-studs around its edge. If you lack a took for pulling out this kind of stud then lever the head of the centre-pin out a few mm with a flathead screwdriver and then slide it clear with pliers. The body of the stud should now slide out easily.

* The car may need lowering to remove the under-tray and re-lifting, as the jacking-point lies in the centre of it.

3. Remove the 7 hex-head screws around the inside of the wheel-arch. as well as two at the leading edge of the under-tray, unseat the inner wheel-arch from around the lip of the wheel-arch itself and pull the plastic inner-arch down out of the way.

* The water-tank for the windscreen and headlight washer-system is located just behind the wheel-arch, below the front of the driver's door. Not the Intensive cleaning-system, which has both the tank and pump under the bonnet.

4. Unplug the wire-connector from the pump in centre of the tank**, by sliding a flat screwdriver into the clip and lifting it upwards.

5. Pull the slim hose-connector clear of the central pump** and allow the tank to drain.

This is a good point to test the washer system one last time to make sure it isn't a blocked hose and the pump is getting no water.

6. Gently twist and pull the pump upwards about an inch out of its mount, then remove the black rubber-bush it sits in.

7. Flush the tank several times by pouring water into the filler-nozzle under the bonnet and allowing it to drain through and clean around the lip of the pump-mount. Check the pump for clogging.

8. Replace the rubber-bush to the tank and, using the new pump if necessary, reverse the procedure.

** The pump in the centre of the tank with the slim hose is for the windscreen washers. The left-hand pump with the larger hose is for the headlight washers.

*** The black connector on the inner corner of the tank is the level-indicator probe. This is also a push fit and the best place to drain from, after removing the wire-connector as above.

E39: Windscreen Washer-Jet System Problems

Replacing / Unblocking the Pump - How to Guide: http://www.planet5.co.cc/2011/10/replacing-unclogging-washer-jet-pump.html

I've had a couple of minor faults with the windscreen/headlamp washer jet and they look like they could be common to most E39 models.

1. Disconnected/Broken Nozzle Hose:

Fault Finding: One washer-nozzle is not working at all / only emitting a tiny amount of water, while the other remains functional.

The hoses for the windscreen-washer run up the offside bonnet-hinge and along the back of the bonnet to reach the nozzels. Due to the constrictive nature of the plastic crimp-clips used to hold them in place, the hoses can be stressed while the bonnet is repeatedly opened and shut. This will most likely cause the plastic-connector to become unplugged from the nozzle [as with my car] so it's just a case of snapping the two connectors back together. The hoses could also be caused to split, so if the connectors are still in place then operate the system and check for leaks along the hose. You will probably need a replacement hose if it is split, unless it is near enough to the nozzle to chop off the split section and reseat it. If there is no leak then it is likely that the hose has been crimped shut, so check each plastic crimp-clip attaching it to the bodywork and adjust it so there's no restriction.

If you suspect you have this problem then check it over as soon as possible as there will be water/screenwash pouring down the back of the engine every time you use the washer system!!

2. Blocked / Faulty In-Tank Pump:

Fault finding: Both wash-jets are not emitting water, or emitting a small amount of water then stopping. No sound can be heard from the washer-jet pump, or the pump is very loud and appears to be struggling to get water through.

If there is no sound from the washers then, if the fuse hasn't blown, its likely the pump is dead and needs replacing. If the pump appears to be struggling but not pumping water then first unclip the hose at the join located under the bonnet, half way down the lip of the driver's wing and try the washers. If water isn't getting this far then a blocked hose/nozzle can be ruled out and the pump will need removing and replacing to unblock.