E46 318i: Front-of-cat o2 / Lambda sensor replacement [Fault Code 271D, 271A, 271B] [Rear-of-cat 271C, 271F]

E46 failed its MOT on the O/S rear tyre and O2 emissions too high. I duly replaced both rear tyres with a new pair sourced through work for just £23 each and they are V-rated so should be ok for the Touring. As for the O2 level being too high, I was told this was a fault with an O2 / Lambda sensor so I plugged in a Snap On Modis scanner to see if this was right.

The code I got back was 271D, as in pic above, which is the up-stream or 'front-of-cat' sensor heating. Codes 271A and 271B show fault at the same sensor, but are labelled directly 'front-ofcat-sensor' with no heating suffix. This sensor is located slightly forward of the catalytic-convert mounted about halfway down the car's underside, as in the diagram below. The one shown to the rear of the cat is the down-stream or 'rear-of-cat' sensor. Code 271C applies to this rear sensor, along with 271E for Rear O2 sensor-heating. The two sensors, though essentially the same, are different parts and part numbers due to the rear sensor having a longer wire. [List of emission based fault-codes here.]

I got hold of a used sensor taken from another E46 318i from www.marobmwspares.co.uk for £18. I prefer used OWM BMW parts that come with a warranty / guarantee over cheap spurious items. The least expensive spurious items start at about £20 for a sensor that can be used for either front or rear of cat, having a long wire than can be cut to length with two bare wire or universal wire-terminal ends that require the original plug to be soldered on from the broken sensor. On the other end of the spurious price range was Euro Car Parts, who offer an OEM-quality sensor for £68, which is pricey but comes with the correct wire-length and plug fitted.

My old sensor proved very tricky to remove with the car on fixed-ramps and I would not like to attempt it with jack and axle-stands. I was unable to crack the sensor off and unscrew it even with the use of special Lambda-sensor sockets and it began to round so I ended up booking ramp-time in the workshop of the company where I work and lifted the E46 Touring on a 2-post ramp to give loads of access underneath. To avoid the risk of breaking the Lambda-sockets or further rounding the sensor itself, I decided to cut about half of the sensor off using a 3.5" cutting-disc and used a 22mm deep impact-socket with a long breaker-bar to finally crack the sensor off. It was pretty seized on, but once cracked just unscrewed by hand. The replacement sensor screwed straight in and swapping / mounting the plug was easy to make for a 5-10-minute job once the car was positioned on the ramp legs.

RESULTS:

The emission test result went from 2.2, with a maximum of 2.0 allowed, down to just 1.0 with the faulty sensor replaced. There is also a significant drop in neat-petrol smell emitting from the rear of the car when it is started from cold, so I'm glad this problem showed itself and got fixed.

Article on /BMWTech subreddit: https://www.reddit.com/r/BmwTech/comments/d5v30t/271d_lambda_sensor_front_of_cat_which_one_there/

F10/F11: DPF Replacement / Removal - EASY GUIDE!

If you are removing your DPF and re-mapping, or if your filter is clogged past the point of a re-gen, then you will need take it off. Getting the DPF / catalytic-converter off an F10 is easier than it looks and is totally doable at home without a set of workshop ramps. I managed with a jack / axle-stand and without removing the exhaust or any of the engine.

1. Safely raise the car.

2. Under the car, remove the centre under-tray that covers the exhaust joint to the DPF by undoing a series of 8mm screws.

3. Loosen the collar-bolt at the joint between the front section of the exhaust and the flexi coming from the DPF using a 14mm socket.

4. Slide the exhaust back about an inch until it pops out of the sleeve in the DPF. [It may help here to pop the exhaust out of the centre rubber-hanger to give more rearward movement.]

5. Under the bonnet, unplug the two O2-sensors and the Lambda sensor, then pull the hose off the metal-tube that runs to the pressure-sensor. Free up the wiring.

6. Remove the upward-facing O2-sensor using a 14mm open-ended wrench.

** Access to the bolts and sensors may be easier with the plastic air-inlet loosened and moved out of the way. **

7. Loosen the collar-bolt joining the front of the DPF to the back of the turbo using a 13mm socket on a long extension and move the collar forward away from the DPF.

8. Remove the upper nut and lower bolt holding the bracket to the rear of the DPF using a 13mm wrench.

9. Remove the two bolts holding the bracket to the back of the engine-block using an E10 double-hex socket, or an 8mm ring-spanner and fully remove the bracket.

10. The DPF will likely be solid in place, so the best bet is to wiggle it from underneath car until it breaks free and can be safely lowered down.

11. With the DPF free, getting it out of the engine-bay is still not a walk in the park. The lower O2 sensor and/or Lambda sensor may need to be removed to get the angle required to slide the body of the DPF down past the steering-knuckle and foil heat shield, which may need to pressed in towards the body a bit to give enough clearance. Eventually, the DPF can be manipulated down through the gap and drop down under the car, so watch out if you have it raised a fair bit off the ground.

12. Re-fitting is a reverse of the above steps. Note, all but the lower O2-sensor should be fitted after the DPF is secured in position. The easiest way to reposition the DPF is get someone to hold it from below high enough for you to get hold of it from inside the engine-bay and lift it up into position, rather than one person trying to reposition it from underneath.

F10 / F11: Front Bumper Removal Guide

** If you are removing / replacing only one side headlight, then it is possible to loosen the bumper on the corresponding side and peel it back to access the headlight screws, rather than removing the entire bumper. **

1. Under the bonnet/hood remove the front end of the rubber seal located just inside the front wings either side.

2. Remove the two plastic push-pin type fasteners on each top corner of the bumper skin. (Or just the ones on the side you are removing the headlight on.)

3. Remove the 4 screws holding the top edge of the bumper using a T30 Torx socket.

4. Under the car, remove the 8 screws under the bottom lip of the bumper using an 8mm socket.


5. There are 3 screws located at the forward side of each front wheel-arch that need removing using an 8mm socket, locations pictured. (If you are working on one side/headlight then these screws only need removing on the corresponding side, as with steps 6 and 7.)


6. Peel the plastic wheel-arch liner back from the corner of the bumper and wedge it against the tyre.

7. Remove the 2 screws located on the inside of the bumper on each side that can now be accessed with the arch-liner out of the way, as pictured. The near one needs a 10mm socket, the one further in is another 8mm. A 1/4" drive wrench is good here with not much room.

8. Gently pull the bumper outwards from its bracket until it separates from the front wing and pull that side of the bumper forward. It should peel away from the car quite easily. Repeat for the other side and the bumper is off, unless you are only working on one side as the headlight and other parts inside / behind the bumper are accessible with one side pulled away from the car.

9. If you are completely removing the front bumper, remember to unplug the front fog-lamps, parking-sensors etc. before moving the bumper away from the car. There is plenty of room to do this with the O/S (right-side) bumper peeled off.


Many thanks to Isturbointeg on F10post.com for some of his superb pictures I made use of. His original guide on F10post forum is here - https://f10.5post.com/forums/showthread.php?t=1187122

F10 530d: Clutch Replacement [Manual 520d, 530d, 535d, F10, F11]

The clutch on my F10 has felt like it's on the way out for about a year now and over the last month or two I've noticed it starting to slip a few times, mainly when moving off in first gear with the car pointing uphill. Time to throw a new clutch in, one of my least favourite jobs and just as with everything on the 5 Series, way more involved a process than swapping a clutch into a Ford Focus. Even I was tempted to just leave the F10 with someone to do the clutch for me, but with quotes in the £1000 - £1500 range I figured it was better to bite the bullet and do it on the drive. Just as well too, as you can see from the pics to the right just how far gone the clutch was, with hardly any face left on the friction-plate and some lovely hot spots on the pressure-plate! Nice.

I'd love to say this job is the same as the E39/E60, which are pretty straight forward, but it is trickier due to updates in the car's design. The main difference is in the prop-shaft removal, the F10 requiring the rear gearbox-mount to be removed to access the bolts to the coupling. This makes it almost impossible to move the car to rotate the prop and access the top bolts, so a bit more ingenuity is needed. I also notice that the gearbox must be lowered in order to remove the slave-clyinder, which is wedged up in the trans-tunnel, something that was not necessary on the E39 and E60. The hose to the slave-cylinder also needs to be unplugged and fluid drained so the gearbox can be lowered. This is an added annoyance that BMW have engineered in here.

** Before you undertake this job yourself, it should be understood that 5-ers are complicated cars and a lot needs to be removed before the gearbox / clutch can be accessed. This is a short list...

• Main under-tray and both side trays.
• Exhaust.
• Two heat-shields.
• Brackets.
• Rear gearbox mount and bracket on back of gearbox.
• Propshaft coupling and centre-bearing.
• Starter-motor.
• Hose to slave-cylinder. [inc. refilling and bleeding of clutch].
• Only now can you remove the gearbox and swap the clutch...

But hey, if you have made it to this guide then chances are you aren't fazed by this kind of thing! So read on... the whole job can be done at home over a weekend by yourself, taking your time and enjoying yourself... or could be done in one day by two of you...

PROCESS:

** Disconnect the battery negative-terminal and put it safely out of the way. **

1. Remove the front belly-pan under-tray located below the engine and gearbox. It is held in place by 8mm screws all around the edges and a couple in the middle.

2. Remove the left and right middle under-trays. These are located under the sill on each side and held on by a lot of 8mm screws and some plastic clips.

3. Remove the centre cross-brace by undoing the eight 13mm bolts, four on each side. This is a steel plate that runs across from left-to-right near the back of the prop-shaft.

4. Remove the exhaust up to the down-pipe. First loosen the 16mm nut on the flange connecting it to the down-pipe at the front. There are then two rubber-hangers, one next to the rear-axle and one to the front of the back-box. A third rubber-hanger is located to the front of the exhaust, not far back from the down-pipe and this can be separated on its bracket by removing the two screws using an E10 double-hex (female-torx) socket. Finally there is a 13mm nut holding a bracket at the very back, up inside the rear-bumper. The exhaust can now be carefully lowered [watching the rubber-bush that has no purpose on the right of the back-box does not get caught in the bumper], worked free of the flange on the down-pipe and fully removed. If the car is high-up on a lift then you will likely need a second person for the last bit.

5. Remove the main heat-shield located above the exhaust. It is held on by several large, flat metal nuts that can be loosened with a 10mm wrench and then spun off by hand.

6. Remove the aluminium bracket that sits around the centre-bearing of the prop-shaft by undoing the two 8mm bolts holding it to the bearing and wiggling it free.

7a. Place a jack or suitable stand under the gearbox to support it so the rear mount can be removed. 

7b. Remove the rear gearbox mount by undoing the three 13mm bolts on each side holding it to the car and a single 13mm nut in the centre that holds it to the rubber-mount on the gearbox.

8a. Remove the braided electrical-earth strap at the back of the gearbox by undoing the 13mm nut attaching it to the body.

8b. Remove the bracket at the back of the gearbox that attaches it to the rear mount, by undoing the four bolts using a T55 Torx socket. Make sure the socket has good purchase here, as it can slip out easily and round the edges of the bolt-head.

9. Remove the 3 bolts holding the prop-shaft coupling (donut) to the back of the gearbox using an 18mm wrench on either side of the nut/bolt. The bolts on the upper side of the prop-coupling are difficult to get to up in the trans-tunnel. If the rear wheels are not lifted and the prop cannot be turned to get to the bolts, it is possible to get them with CV-joint type sockets as I did.

10. Undo the bracket holding the centre-bearing of the prop-shaft by removing the 13mm nut either side.

11. Uncouple the prop-shaft from the gearbox by pulling the centre-bearing down enough for the locating pin on the gearbox to be clear of the prop-coupling. The front of the prop can now be lowered and moved to the side. If you have the whole car raised on a lift, then you will need to support the front of the prop, or remove the rear coupling to the diff. and get someone else to help you lift it down.

12. Remove the live terminal from the starter-motor using a 13mm wrench and the earth-terminal using a 10mm wrench.

13. Remove the 3 screws holding the starter-motor to the engine using an E10 double-hex socket and work the starter-motor out from the gearbox.

14. Disconnect the reverse-light switch by depressing the metal wire-clip to remove the plug and unclip the wire along the gearbox.

15. Clamp the rubber-hose to the clutch slave-cylinder and disconnect the clutch-line where the slim metal tube enters the slave-cylinder. This is done by prising the metal-clip out of the connector with a small flat-screwdriver and pulling the rubber-seal out of the slave-cylinder. Don't worry too much if you cannot clamp the clutch-hose, but it will involve more bleeding later on, which is a nightmare.

16. Remove the four bolts from the lower half of the gearbox bell-housing attaching it to the sump using an E10 double-hex socket.

17. Remove the remaining 6 large bolts from the gearbox bell-housing holding it to the engine-block using an E12 double-hex socket. [As in diagram.] The 2 down each side of the bell-housing are easy enough to access, but the 2 at the top are quite tricky. There is no easy way to get them, so it might be worth feeling around the top of the gearbox with the socket only until it is on the bolt and then get the ratchet / extension bar or CV-jointed socket to them.



** CAUTION: The gearbox will now be loose and held to the engine only with the locating-pegs, so ensure it is safely supported! **

18. Gently prise the gearbox away from the engine until it is clear of the locating-pegs and held up only by the centre-spline. Rocking it side-to-side should also help here. Draw the gearbox back slowly until the centre-spline is clear of the clutch/flywheel and the gearbox can be safely lowered partially. ONLY LOWER IT ABOUT HALF WAY!

19. Disconnect the wiring-connector from the cars neutral-sensor, located at the top of the gearbox by reaching around the top while it is partially lowered and pressing in the plastic clip on the connector. Fully lowering the gearbox before disconnecting will stretch the wire and potentially snap it!

20. Fully lower the gearbox safely onto the ground.

21. The clutch is now accessible, bolted to the back of the flywheel at the back of the engine. The clutch is removed by undoing the 6 bolts around its circumference using a 6mm allen-key socket [shown in photo]. The clutch can now be prised away from the engine! Be careful the clutch does not drop at this point, so it is best to support it with one hand while loosening the final bolt.

22. Remove the release-module / bearing from the spline inside the gearbox bell-housing. The metal lever should be held in place on the opposite side to the slave-cyinder by a piece of metal-wire and after removing that it should easily pull off. [If your clutch-kit includes a new release-module that is - if you are not replacing this then leave the old one in place.]

RELAX! You are now half way through the job!

23. Clip the new bearing into the new release-module as per the clutch-kit instructions and refit it to the spline in the gearbox bell-housing, replacing the wire-clip.

24. Fit the new clutch friction-plate into the new pressure-plate and mount it to the back of the engine leaving the 6mm allen-bolts loose by a few turns so the friction-plate can be moved around inside, but will hold in position.

25. Use the correct clutch alignment-tool to centralise the clutch, or if you do not have one look directly into the centre bore of the clutch and centralise the friction-plate by hand. It does not have to be perfectly in the centre, so you can get it accurate within about 0.5mm by eye.

26. Fully tighten the 6mm all-bolts.

27. Partially raise the gearbox to leave a few inches clearance above it and reconnect the wire to the neutral-sensor.

28. Fully raise the gearbox so it is in line with the back of the engine and move it forward, guiding the centre-spline into the clutch. Rocking the gearbox left-to-right should locate the spline into the clutch plate without too much fuss and it should then be able to rotate into position to meet the locating studs. The main problem here is the height and pitch of the gearbox on the jack / gearbox-stand, so watch out for differences in the gap at the top and bottom of the bell-housing when marrying it up.

29. Reverse steps 17 to 7. For tightening-torques refer to this post - http://www.beemerlab.org/2018/11/bmw-tightening-torques.html

30. Bleed the clutch - if you clamped the hose you shouldn't have too much trouble bleeding it, but the nipple is difficult to access and it can be easy to let air back in, so I have devoted a post to my bleeding issues here - F10: Clutch Bleeding Guide... the whole nightmare! [Manual transmission / gearbox 520d, 530d, F10, F11, G07, E90, E92 3er etc.]

31. Reverse steps 6 to 1.

E60: Replacing Rear Rose-Bushes / Lower Ball-Joints

These are the main joint where the rear wheel-hubs attach to the trailing-arms and are a pretty common replacement on high mileage 5 and 7 series. They were the advisories I got on the MOT in February, so thought I should get them done before the nice weather ends.

DIFFICULTY - 6/10 This is not a long or complicated job, but is quite labour intensive.

** YOU WILL NEED: A dedicated removal / installation tool. These are available on eBay [here] for just under £40 and work for all modern 5, 6, 7, X5 and X6 rose-bushes. These are all copies of the BMW special tools listed here on TIS.

The rose-bush is item 2 in the diagram.

1. Lift car, remove rear wheel, support on axle-stand.

2. Unbolt the anti-roll bar link from the trailing-arm using an 18mm open/ring spanner on the nut from underneath, while holding the stud from turning using a T40 Torx socket through the centre of the spanner.

3. Loosen the long bolt that holds the trailing-arm to the wheel hub [5] using a 24mm wrench on the nut and an 18mm wrench on the bolt head. [A long breaker-bar is advisable on the nut.]

4. Loosen off the eccentric-bolt on the trailing-arm [11] using an 18mm wrench on the bolt head and a 21mm wrench on the nut. [Be careful not to turn the bolt and alter the alignment as it's hard to get back.]

5. Loosen off the other bolt on the trailing arm [9] using an 18mm wrench on both the nut and bolt head.

6. Fully remove the 24mm nut [6] and long bolt [5] from the wheel-hub. [The bolt will likely need knocking out with a drift.]

7. Remove the bolt holding the push-rod to the wheel-hub [7] using an 18mm wrench.

7a. (O/S trailing-arm only) - Disconnect the suspension-angle sensor from the trailing-arm using a 10mm wrench and 10mm open-end spanner.

8. Lever the trailing arm down so it is clear of the wheel-hub and the push-rod [4] can be removed.

9. Remove the retaining-ring [3] from the rear face of the rose-bush. [It will likely be well seized in place and need splitting with a grinder / cut-off tool before knocking out in two pieces.]

10. Set up the removal-tool either side of the rose-bush with the largest mandrel on the receiving side and the smallest mandrel on the pushing side, ensuring the pushing side is completely flush to the rose-bush face. [Some of the rose-bush rubber boot may need cutting off to ensure this.]

11. Tighten up the removal-tool using a 19mm wrench on either side until the bush pops out of the wheel-hub. [Rotating the receiving mandrel round so the notched area can be viewed from underneath shows the progress of the bush coming out.] [The bush may well need some heat treatment if it is seized, or you can have a go at splitting it if you are brave enough.]

12. Place the new rose-bush into the hub, ensuring it is straight to the collar and will go in evenly. [The bush always slots it from front to rear, with the retaining ring on the rear face.]

13. Set up the removal-tool on the new rose-bush with the largest mandrel on the receiving side again and the mid-sized mandrel on the pushing side. [The notched side of the receiving mandrel will need rotating so it fits flush past the back of the brake disc. This is essential to keep the threaded-bar / bush straight.]

14. Tighten up the removal-tool with two 19mm wrenches until the bush is fully seated in the collar. [The bush should slide in pretty easily, if it resists then it is not going in straight. A small amount of copper grease can be rubbed round the bush to aid it, but be very sparing.]

15. Fit the new retaining-ring to the rear face of the rose-bush.

16. Refit the push-rod and trailing arm etc. as a reversal of steps 8 to 1.

** For correct re-alignment of suspension geometry see this post. **

E60 Diesel: Replace Turbo Waste-Gate [Actuator]

This is a pretty easy job and can be done with removing the turbo, exhaust-manifold or rocker cover.

1. Remove the inlet duct to the air-filter housing. It's held by a T30-Torx screw at the front and just unclips from the housing.
2. Remove the boost-pipe from the top of the turbo by removing the screw from the left side of where it joins to the turbo using a 10mm wrench, then loosening the right hand screw using a T30-Torx socket and rotating the collar clockwise until it can be pulled out of the turbo.
3. Remove the other end of the boost-pipe from the left side of the intercooler by reaching from underneath with a flathead screwdriver and sliding the metal clip down. The pipe should pop the intercooler easily and be pulled out from above. [This can be done without fully removing the engine-undertrays].
4. Gently slide the rubber vacuum-hose off the metal spout on the waste-gate.
5. Remove the three screws holding the waste-gate to the turbo using a 10mm wrench. [There is just enough room down the left side of the engine to get a ring-spanner on, otherwise a ratchet with a short extension-bar may get them more easily].
6. Push a cloth or some tissue roll down under the bottom of the waste-gate between the turbo inlet and exhaust wheels to stop the retaining-clip getting lost into the engine and slide the clip off the waste-gate arm using a long flat screwdriver. [There is just enough clearance to get an angle with the screwdriver and just about see the clip. The clip will probably have to be removed with a stick-magnet].
7. Slide the waste-gate arm off the stud and remove it.
8. Refit the new waste-gate as a reversal of above, being careful not to lose the retaining-clip during refitting. The clip may need holding in position with a stick-magnet as it is pushed down with a flat screwdriver.

E60 Diesel: Replacing the Front Turbo Housing/Volute

**The turbo needs to be removed. Reaching the 8mm nuts at the back of the volute is impossible               with it in situ.

1. Mark a line on the original volute / front-casing where each 8mm screw is located before removing it. It is adjustable and the new one needs to be in the exact same place as the original for correct waste-gate location.
2. Remove the 3 screws holding the waste-gate bracket to the turbo front-casing / volute using a 10mm wrench.
3. Remove the 6 screws holding the front-casing / volute to the turbo and wiggle it free.
4. Hold the new volute up to the original and mark lines in the corresponding places. This is best done with them on a flat surface and holding a straight-edge across both.
5. Slide the new volute on to the turbo and replace the six 8mm screws, ensuring the lines are correctly located before tightening them up. It is alloy-to-steel, so no high-heat gasket-paste is required.
6. Press the waste-gate into the right position for the bracket to meet the holes on the volute and replace the three 10mm screws holding it in place.

Why I replaced mine:

With re-con turbos starting at £350, I went for a used one from a crash damaged 7-Series. Mine is an early E60 and has the vacuum-actuated turbo, so it was handy that the 7er did too as they are hard to source - eBay is full of the electronic-actuated type and I couldn't see a vacuum one, but it may be that they are inter-changeable.

The overall condition of the turbo looked worse than the one I was removing, but there is a bit less play in the spindle-shaft so worth a shot at £200 delivered, let's hope the saving pays off. The only drawback is the front-casing was slightly damaged at the point where the pipe to the intercooler fits, but swapping the original one in was not a difficult job.

E60 Diesel: Remove/Replace Turbocharger

Removing and refitting the turbo itself is not a difficult task, but the mass of other parts that need removing to access it makes this a reasonable amount of effort.

You will first need to remove:

Engine covers. [5mm Allen]

Air inlet ducting and air-filter. [5mm Allen]

Inlet manifold. [10mm + 11mm Hex]

Injector pipes. [17mm open-end wrench]

Injectors. [8mm Hex]

Rocker cover. [10mm deep-Hex]

Turbo to intercooler pipe. [10mm Hex + T30-Torx]

Airbox to turbo pipe. [5mm Allen]

EGR to exh.-manifold pipe. [T45-Torx + 7mm Hex]

Exhaust-manifold. [10mm deep-Hex + 12mm deep-Double-Hex]

Front engine-undertray. [8mm Hex]

Engine reinforcement-plate. [16mm Hex]

Exhaust vibration-damping rods. [13mm Hex]

REMOVAL:

1. Remove the two nuts holding the down-pipe/cat to the back of the turbo using a 17mm wrench and work the down-pipe back off the studs.

2. Remove the banjo-bolt that attaches the turbo oil-feed to the block using a 14mm wrench, remove that end of the oil-feed pipe and loosely screw the banjo-bolt back in a few turns to stop any oil leaking from the block. Put some cloth against the block under the pipe to catch any drips and remove and retain the 2 copper washer-seals as they are easily misplaced.

3. Reach under the turbo, locate where the lower oil-return pipe enters the rubber-hose to the sump and loosen off the upper jubilee-clip using a 6mm-Hex socket or flat screwdriver if you can get access. Let the jubilee-clip slide down the rubber hose.

4. Slide off the rubber-hose that runs to the waste-gate on the turbo.

5. Make sure the turbo's weight is supported, remove the two bolts holding the turbo-bracket to the block using a 13mm wrench and lift the turbo out, carefully sliding the lower oil-return pipe out of the rubber-hose.

FITTING:

6. **Ensure all oil-feed pipes etc. are swapped over to the new turbo**. Lower the new turbo into position, sliding the lower oil-return pipe back into the rubber-hose and loosely refit the two bolts.
7. Tighten the jubilee-clip on the oil-return hose and refit the oil-feed hose back on to the banjo-bolt, making sure the copper-washers are in place either side.
8. Place the exhaust vibration-damping rods back in place to locate the down-pipe and loosely refit the 13mm nuts.
9. Refit the neck of the down-pipe to the back of the turbo and tighten the 17mm nuts.
10. Place the exhaust-manifold over the studs on the cylinder-head and manoeuvre the turbo into a position where the bolts holding it to the manifold can be fitted. It can be trick to do while keeping the gasket aligned. Turn the three manifold-to-turbo bolts using a 12mm deep-Double-Hex (12-sided) socket until the manifold is seated, but do not fully tighten them.
11.  Lift the turbo to take the weight off the manifold and fully tighten the two bolts holding it to the block using a 13mm wrench. They are a pain to get to but it is doable, also a lot easier with someone else lifting the turbo.
12. Replace the twelve copper-nuts that hold the exhaust-manifold to the cyl.-head and tighten them using a 10mm deep 6-sided socket, as the strip easily with 12-sided ones.
13. Tighten the three bolts holding the manifold to the turbo.
14. Re-connect the rubber vacuum-hose to the waste-gate.
15. Refit the other things on the above list.

http://www.instructables.com/id/How-to-replace-Turbocharger-on-BMW-30L-Diesel-E60E/

E36 Compact: M43 Oil Change + Filter Removal.

Got round to changing the oil and filter on the Compact, as I've been running it for a month with the mayonnaise filled concoction left from the dodgy head-gasket / cooling issue.

Removing Oil-Filter:

The filter-housing on the later M43 316i / 318i is right down in the bowels of the engine and impossible to get to easily, as they are on almost all other BMWs. The lid has no nut either to undo it from above, so the only way is to use an old-skool oil-filter removal tool from the side, only most of the engine prevents this.

The simplest way to get it off is to remove the fan-cowl and fan. This way there is just about enough room at the front of the engine to get a turn on the filter with the removal tool. I found a chain based removal tool works well, but a steel-belt one would probably be just as good. It isn't essential, but I removed the top inlet-manifold too, just to see what I was doing more clearly.

1. Remove the fan-cowl by undoing the two top screws with a 10mm socket and lifting it off, popping it out from the air-inlet ducts at either side.

2. Remove the two 8mm screws holding either side of the rear edge of the fan-housing at the top and lift the fan vertically up, sliding it out of the two bottom lugs.

3. Slide the removal-tool in from the front and there should now be room enough to get a turn on the filter-housing lid, even if it's as tight on as mine was.

E60: Engine Swap Week - Day 4

Had a lost day yesterday when the engine didn't arrive. It only turned up at 1.30pm today, so I will have to concentrate on swapping over the high-pressure pump, flywheel and clutch, as well as removing the loom etc. ready to patch mine in. Lifting the engine in will have to wait until tomorrow.

• Replace steering-rack / subframe bolts entirely.
• Remove loom and vacuum-hoses from new engine.
• Swap over high-pressure fuel-pump.
• Fit flywheel and clutch.
• Remove oil filter/cooler and rocker-cover for lifting.
• Match engines entirely.
• Lift engine in.

Engine arrived at 1.30pm.

And was finally sat in the bay at 7.30pm.

E60: Engine Swap Week - Day 3

• Drop prop-shaft.
• Remove slave-cyl. / gearshift linkages.
• Drop gearbox.
• Lift engine out.
• Remove parts for new engine.

Once the prop was down it didn't take long at all to get the engine out. The gearbox is huge, but surprisingly light.

Prep for new engine:

• Remove clutch.
• Remove flywheel.

Got the clutch off easy enough, but need a T55 Torx socket to remove the flywheel so that will have to wait until I get it from work tomorrow.

NOTE: Missing bolt from exhaust cross-member.

E60: Engine Swap Week - Day 2

• Remove headlights and front crash-bar.
• Remove starter motor.
• Remove oil filter / cooler.
• Photograph and disconnect vacuum hoses and wiring-connectors.
• Attempt remove engine.
• Remove exhaust-system.
• Remove heat-shield.
• Remove gearbox mounts.
• Remove 2 of 3 prop-shaft bolts [coupling to gearbox].

Sadly, the first attempt did not work. The sump still gets stuck on the sub-frame. TIS says to first remove the prop and gearbox, so it looks like this is the only way.

POA for Day 3:

1. Bolt gearbox mount back up.

2. Loosen remaining prop-shaft bolt.

3. Lift car and put axle-stand under jacking point.

4. Support gearbox and remove mounts.

5. Drop prop-shaft.

NOTE: Cut off rubber exhaust-hanger needs new - Part no. 18207578238

Blue nylon rope not the best for lifting engines, but note a lot of weight is removed from the engine - head, ATF-pump, oil filter-cooler, A/C comp etc.

E60: Engine Swap Week - Day 1

• Remove all slam-panel and grilles / trim.
• Drain and remove radiator.
• Remove drive-belts.
• Bleed air-con, remove a/c radiator and compressor.
• Drain PAS-fluid, remove PAS-pump and cooler.
• Remove alternator.
• Remove intercooler.
• Disconnect and remove injectors / fuel-rail.
• Disconnect wiring-loom from ECU / relay-box.

NOTE: Broken T-piece on injector leak-off hose needs replacing if doesn't come with engine. [Part no. - 13537789364].

E60: Removing Acoustic Engine-Covers for 6-Cyl. Diesels [525d, 530d, 535d]

Engine Acoustic Covers:

1. Remove the five screws holding the main engine-cover using a 5mm allen-key or male-hex socket and lift it off. The screws are located one either side at the front and rear and the fifth next to the PAS fluid cap.

2. Remove the left and right pollen-filter from the plastic panels by popping off the metal-clip and undoing the plastic nut with the arrow a 1/4 turn using a 13mm socket.

3. Disconnect the wiring connector for the 'bonnet-open' switch, located on the left hand plastic heater-duct in front of the pollen-filter.

4. Remove the left and right plastic air-duct panels from the back of the engine-bay under the windscreen by undoing the plastic nuts with the arrow a 1/4 turn using a 13mm socket. The nuts are located one either side under the pollen-filter and one in the middle joining both panels.

5. Remove the strut-brace by undoing the bolt holding on either side holding it to the suspension turrets and the two in the middle using an E12 double-hex or star socket.

6. Remove the two screws holding the rear engine-cover, one either side, using a 5mm male-hex socket or Allen-key and lift it off.

Air-box Housing / Air-Filter Inlet: