Well, fine. If
everyone else is going to scratch-build Night Scythes and Doom Scythes, I might
as well, too...
First off, this isn’t going to be spectacular, so if you’re
looking for something on par with the Plaguereaper or the Rhino fleet, I’m
afraid this won’t be it. It’s a safe bet
that Games Workshop is going to put out an actual Doom/ Night Scythe model when
the next big Necron release happens, and a few weeks after that there are going
to be a ton of great templates by people much more skilled (and with more free
time) than me. I’m looking to make
something that will be a quick, decent stand-in for now.
And, as usual, I want to do it cheap.
I’m not doing templates for this, so I may be
over-describing things a bit to make it easier to follow along. Also, for most of this post, I’m just going
to call it a Scythe. We can get
particular next time when I do details.
Let’s start with the basics.
I decided the outside edge of the Scythe was probably close to an 8 1/2”
circle. How did I decide this
size? Well, someone over at the Bell of
(LINK) Lost Souls cleverly pointed out that the Scythe sprues would have to fit
in the existing boxes. The inside of
your standard Chimera/ Rhino/ Monolith box measures 11 1/4” x 8 7/8”. I’m also going off the assumption that the
hull is going to be mostly one piece (maybe a top and a bottom section).
I drew two diagonals to find the center of a frozen pizza
box. Then, using a compass, I drew out
an 8 1/2” circle. I also drew a line
that went straight through the center point.
This is going to be a front-back reference line for the model.
Helpful Hint – The model is going to need four
of these shapes. I found it was easier to do
all four at once for each step, because it meant less resetting the compass. Your results may vary...
Next, I measured down 1 3/4” from the center point and made
a second mark. Off this, I used the compass
to make a 4 1/2” circle inside the first
one. Note that they don’t quite touch. I also marked the center point. The compass leaves a mark, but I wanted it to
be clear because I’m going to be using it as a reference point. It may seem
obvious, but this is the empty space “inside” the Scythe or between its wings,
depending on how you view it. Right at the front, I went out 1 1/4” from the centerline on either side. I made a few measurements and then made two short front-to-back lines parallel to the center line. These are marking off the end of the wings and the gap that stretches across the front of the scythe.
Now, going off the center point of the smaller circle, I
drew lines extending out over the hull and wings at 45 degree angles. These are going to help me place the sloped
armor on the Scythe. I just want to do
all the marks while this is big, flat, and solid. Cutting’s the last thing I’ll do.
I also did a pair of lines that were 30 degrees off the
center line. These are for the cockpit
section and the smaller armor sections at the front.
This Is Important – Remember, none of
these angled/ radiating lines are cut lines.
They’re just a reference for later
Once I had all this, it was time to cut. Also, I was careful to save the center
sections—they might be useful for the cockpit.
You’ll notice the Necron Warrior gives us a good sense of scale, and you
can compare him to the codex art-image of the pilot up above.
Helpful Hint – These circles are big enough
that you can cut the whole thing out with a good pair of scissors. I just took my time and went slow. It took about three minutes for each one.
Once I had all four sections cut out, I checked which pairs
lined up best and glued them together. I
double-checked that they were lined up right, wrapped them in wax paper, and
set them under a hardcover copy of Under
The Dome and a few other Stephen King epics to make sure they stayed flat. I let them dry overnight.
And for now, that’ll be it.
No post next week because of Thanksgiving, but I’ll probably
do two the week after just to get this done.
