
Concept explainers
The three important areas of home.

Explanation of Solution
The three important areas of home are living room, bedroom and dining room.
Living room
It consists of the living, nook areas, dining, family and den areas. These are the rooms or areas of a house where friends and family will spend most of their leisure time. The rooms in the living area should be clustered together near the entry to allow easy access for guests. Points to consider during planning the living room include how often the room will be used, how many people are going to use it. The type and size of the furniture that will be placed in the living room. Some families use the living room as a place for quiet conversation and depend on other living areas for noisier activities.
Bedroom:
The arrangement of bedrooms greatly varies depending on the family's needs. Common arrangements include placing the master bedroom separate from the bedrooms, for children or placing all the bedrooms together. It is also common in custom homes to plan a bedroom living unit for long term care of live-in relatives. Bedrooms are normally located with access from a hallway for privacy from living areas and should be near to the bathrooms.
Dining room:
Dining areas, depending on the size and atmosphere of the residence. The dining area is often part of or adjoins, the living area. For a more formal eating environment, the dining area will be near but separate from the living room area. The two areas are usually adjoining so that guests may go easily from one area to the other without passing through other areas of the house. A casual dining room can be as small as
Want to see more full solutions like this?
Chapter 10 Solutions
Architectural Drafting and Design (MindTap Course List)
- The structures in the following problems are single-story, one-bay assemblies representing one common lateral force- resisting systems used in buildings: Moment-Resisting Frames (MRFS). Each frame is fix-connected at its base. Your tasks are as follows: 1. 2. Solve for the support reactions (vertical, lateral, and moment) under the applied lateral load. Determine member end forces (axial, shear, and moment) for all relevant structural members.arrow_forwardThe structures in the following problems are single-story, one-bay assemblies representing one common lateral force- resisting systems used in buildings: Moment-Resisting Frames (MRFs). Each frame is fix-connected at its base. Your tasks are as follows: Solve for the support reactions (vertical, lateral, and moment) under the applied lateral load. Determine member end forces (axial, shear, and moment) for all relevant structural members. 1. 2. 3. Draw internal force diagrams (bending moment) for the required elements. 4. Determine the lateral deflection of joint B Be sure to clearly label your diagrams and show all work leading to your solutions. You must use the slope deflection equations to solve the problem, otherwise it will take forever. Use dimensions referenced to elements' centerlines. You shall neglect axial and shear induced deformations.arrow_forwardWhat are some relative code requirements specific to a roof system components?arrow_forward
- The ____________ costs can often be the determining factor in a successful project. Group of answer choices Overhead Material Labor Profitarrow_forwardWho is responsible for conducting special inspections and ensuring the work completed complies with design documents and referenced standards, why are specical inspections required?arrow_forwardYou are viewing Attempt 1/Continue Work * Incorrect The 123-kg industrial door with mass center at G is being positioned for repair by insertion of the 8° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. If the coefficients of static friction at both the top and bottom wedge surfaces are 0.65, determine the force P required to lift the door at B. Assume a = 1.4 m, b = 1.2 m, a = 8° A Answer: P = 1144.28 N Barrow_forward
- How can new sustainable materials change dead load calculations in future designs in earthquake-prone areas?arrow_forwardGiven the truss with loading shown. Note that the roller connection at Joint D is in atrack so that it cannot move in the x-direction, but it can roll in the y-direction.Solve the truss with the virtual load you would use if you are going to solve for the verticaldeflection at Joint E using the method of virtual work.Note: Just solve the truss. You DO NOT need to find the vertical deflection at Joint E.arrow_forwardQuestion (1): (18 Marks) Gaza City has a total population of 650,000 inhabitant, where 75% of the population is connected to wastewater collection system. The water consumption per capita is 100 L/day. Currently, the collected flow treated partially by aerated lagoon system. The municipality intend to change the treatment system to a completely mixed activated sludge system to be used for organic matter removal only to fulfill the Palestinian standards for reuse (Soluble BOD 30 mg/l). The given data from the municipality laboratory and assumptions: ⚫ The influent soluble Biological Oxygen demand = 500 mg/l. Biomass yield (Y) = 0.5 mg VSS/mg BOD removed • Endogenous decay rate constant (Ka) = 0.05d¹ • • The concentration of biomass (X) = 3000 mg MLVSS The concentration of recycled biomass (X) = 10000 mg MLVSS/L Growth rate (d) 2.5 1.25 100 For the completely mixed activated sludge system find the following: a) The average flow to the treatment plant. b) The mean cell residence time. c)…arrow_forward
- Question (3): (20 Marks) You have been assigned to design a secondary wastewater treatment component based on a tricking filter technique. The flow rate is 3500 m³/day, the raw wastewater has a BOD5 of 600 mg/l. This wastewater is primarily treated with an efficiency of 35%. • Assume suitable design criteria to obtain a BOD effluent of 15 mg/l. Design the secondary clarifier • Perform all the necessary cheeks on your design.arrow_forwardQuestion (3): (20 Marks) You have been assigned to design a secondary wastewater treatment component based on a tricking filter technique. The flow rate is 3500 m³/day, the raw wastewater has a BOD5 of 600 mg/l. This wastewater is primarily treated with an efficiency of 35%. • Assume suitable design criteria to obtain a BOD effluent of 15 mg/l. Design the secondary clarifier • Perform all the necessary cheeks on your design.arrow_forwardData:Total budget = $25,000BCWS = $ 8,333BCWP = $ 6,400ACWP = $ 7,800Project duration = 40 daysData date: 10 days Perform the following analyses of the project based on the data given above.a. Cost Variance b. Schedule Variancearrow_forward
- Architectural Drafting and Design (MindTap Course...Civil EngineeringISBN:9781285165738Author:Alan Jefferis, David A. Madsen, David P. MadsenPublisher:Cengage LearningResidential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781285852225Author:Gregory W FletcherPublisher:Cengage Learning

