Q3) The circuit shown in Figure below is the Norton equivalent circuit of the circuit. Find the value of the short-circuit current isc and Thevenin resistance Rt, verify the result using Pspice. 30 www 10 V 2ia ia www 5Ω W 6 Ω isc R₁ Show Transcribed Text ان с Q3) For the circuit of Figure below, the current i has been measured for three different values of R and is listed in the table. Are the data consistent? 1 ΚΩ 4 ΚΩ R(Q) i(mA) 5000i 5000 16.5 + 500 43.8 0 97.2 R 4 ΚΩ 10 V

Q3) The circuit shown in Figure below is the Norton equivalent circuit of the circuit. Find the value of the short-circuit current isc and Thevenin resistance Rt, verify the result using Pspice. 30 www 10 V 2ia ia www 5Ω W 6 Ω isc R₁ Show Transcribed Text ان с Q3) For the circuit of Figure below, the current i has been measured for three different values of R and is listed in the table. Are the data consistent? 1 ΚΩ 4 ΚΩ R(Q) i(mA) 5000i 5000 16.5 + 500 43.8 0 97.2 R 4 ΚΩ 10 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.
You are an electrician on the job. The electrical blueprint shows that eight 500-W lamps are to be installed on the same circuit. The circuit voltage is 277 V and is protected by a 20-A circuit breaker. A continuous-use circuit can be loaded to only 80% of its rating. Is a 20-A circuit large enough to carry this load?
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.
An ac resistance is higher than a dc resistance. True False
1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive circuit?
An AC electric motor is connected to a 240-V, 60-Hz source. A clamp-on ammeter with a peak hold function reveals that the motor has an inrush current of 34 A when the motor is first started. Your job is to reduce the inrush current to a value of 20 A by connecting a resistor in series with the motor. The resistor will be shunted out of the circuit after the motor is started. Using an ohmmeter, you find that the motor has a wire resistance of 3 . How much resistance should be connected in series with the motor to reduce the starting current to 20 A?
Schematic diagrams break the wiring of control systems down into a(n) _____ arrangement. a. circuit-by-circuit b. series circuit c. individual circuit d. none of the above
Refer to the formulas in Appendix B in the Resistive-Capacitive Parallel Circuits section. A resistor and capacitor are connected in parallel to a 208-V, 60-Hz power source. An ammeter indicates a total circuit current of 46 amps, and a wattmeter indicates a true power of 4975 W. What is the resistance of the circuit?
3. What is the impedance of the circuit in Question 2?
At what height are the telephone outlets in this residence mounted? Give measurement to center. _____