| 1 | ; AiR-BOOT (c) Copyright 1998-2008 M. Kiewitz
|
|---|
| 2 | ;
|
|---|
| 3 | ; This file is part of AiR-BOOT
|
|---|
| 4 | ;
|
|---|
| 5 | ; AiR-BOOT is free software: you can redistribute it and/or modify it under
|
|---|
| 6 | ; the terms of the GNU General Public License as published by the Free
|
|---|
| 7 | ; Software Foundation, either version 3 of the License, or (at your option)
|
|---|
| 8 | ; any later version.
|
|---|
| 9 | ;
|
|---|
| 10 | ; AiR-BOOT is distributed in the hope that it will be useful, but WITHOUT ANY
|
|---|
| 11 | ; WARRANTY: without even the implied warranty of MERCHANTABILITY or FITNESS
|
|---|
| 12 | ; FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
|
|---|
| 13 | ; details.
|
|---|
| 14 | ;
|
|---|
| 15 | ; You should have received a copy of the GNU General Public License along with
|
|---|
| 16 | ; AiR-BOOT. If not, see <http://www.gnu.org/licenses/>.
|
|---|
| 17 | ;
|
|---|
| 18 | ;---------------------------------------------------------------------------
|
|---|
| 19 | ; AiR-BOOT / DRIVE I/O
|
|---|
| 20 | ;---------------------------------------------------------------------------
|
|---|
| 21 |
|
|---|
| 22 |
|
|---|
| 23 |
|
|---|
| 24 | IFDEF MODULE_NAMES
|
|---|
| 25 | DB 'DRIVEIO',0
|
|---|
| 26 | ENDIF
|
|---|
| 27 |
|
|---|
| 28 | ;
|
|---|
| 29 | ; Check if INT13X extensions are supported.
|
|---|
| 30 | ; AirBoot requires these extensions, and will halt if they are not available.
|
|---|
| 31 | ; Modified: AX, BX, CX, DX, CF
|
|---|
| 32 | DriveIO_CheckFor13extensions Proc Near
|
|---|
| 33 | mov ah, 41h
|
|---|
| 34 | mov bx, 55AAh
|
|---|
| 35 | mov dl, [BIOS_BootDisk] ; We check using the boot-disk
|
|---|
| 36 | int 13h
|
|---|
| 37 | jc PCCF13E_NotFound ; Error occured
|
|---|
| 38 | cmp bx, 0AA55h
|
|---|
| 39 | je PCCF13E_Found
|
|---|
| 40 | PCCF13E_NotFound:
|
|---|
| 41 | ret
|
|---|
| 42 | PCCF13E_Found:
|
|---|
| 43 | and cx, 1 ; Check 42h-44h,47h,48h supported
|
|---|
| 44 | jz PCCF13E_NotFound ; Sig OK but no support, strange beast
|
|---|
| 45 | mov byte ptr [CurIO_UseExtension], 1
|
|---|
| 46 | ret
|
|---|
| 47 | DriveIO_CheckFor13extensions EndP
|
|---|
| 48 |
|
|---|
| 49 |
|
|---|
| 50 | ; Note: Some routines set DS/ES to CS or even address via CS, even if its not
|
|---|
| 51 | ; needed. This was done for SECURITY. So DO NOT remove it.
|
|---|
| 52 | ; Its there to make sure the correct data is loaded/written to/from
|
|---|
| 53 | ; harddrive.
|
|---|
| 54 | ;
|
|---|
| 55 | ; IF YOU MODIFY ANYTHING IN HERE, YOU MAY EASILY BREAK YOUR HARDDRIVE!
|
|---|
| 56 |
|
|---|
| 57 | ; Will only load base-configuration, will NOT load IPT nor Hide-Config
|
|---|
| 58 | ; Those are originally loaded on startup and will NOT get reloaded.
|
|---|
| 59 | DriveIO_LoadConfiguration Proc Near Uses ax bx cx dx es
|
|---|
| 60 |
|
|---|
| 61 | IFDEF AUX_DEBUG
|
|---|
| 62 | IF 0
|
|---|
| 63 | pushf
|
|---|
| 64 | pusha
|
|---|
| 65 | push si
|
|---|
| 66 | mov si, offset $+5
|
|---|
| 67 | jmp @F
|
|---|
| 68 | db 10,'DriveIO_LoadConfiguration:',10,0
|
|---|
| 69 | @@:
|
|---|
| 70 | call AuxIO_Print
|
|---|
| 71 | pop si
|
|---|
| 72 | ;~ call DEBUG_DumpRegisters
|
|---|
| 73 | ;~ call AuxIO_DumpParagraph
|
|---|
| 74 | ;~ call AuxIO_TeletypeNL
|
|---|
| 75 | popa
|
|---|
| 76 | popf
|
|---|
| 77 | ENDIF
|
|---|
| 78 | ENDIF
|
|---|
| 79 |
|
|---|
| 80 | mov ax, cs
|
|---|
| 81 | mov es, ax
|
|---|
| 82 | mov bx, offset Configuration
|
|---|
| 83 | xor dh, dh
|
|---|
| 84 | mov dl, [BIOS_BootDisk] ; Disk we booted from
|
|---|
| 85 | mov cx, 0037h ; Sector 55 (CHS)
|
|---|
| 86 | mov ax, 0201h ; Function 02, read 1 sector...
|
|---|
| 87 | int 13h
|
|---|
| 88 | jnc DIOLC_NoError
|
|---|
| 89 | call MBR_LoadError ; Will Abort BootUp
|
|---|
| 90 | DIOLC_NoError:
|
|---|
| 91 | ret
|
|---|
| 92 | DriveIO_LoadConfiguration EndP
|
|---|
| 93 |
|
|---|
| 94 | DriveIO_SaveConfiguration Proc Near Uses ax bx cx dx ds es si
|
|---|
| 95 |
|
|---|
| 96 | IFDEF AUX_DEBUG
|
|---|
| 97 | IF 0
|
|---|
| 98 | pushf
|
|---|
| 99 | pusha
|
|---|
| 100 | push si
|
|---|
| 101 | mov si, offset $+5
|
|---|
| 102 | jmp @F
|
|---|
| 103 | db 10,'DriveIO_SaveConfiguration:',10,0
|
|---|
| 104 | @@:
|
|---|
| 105 | call AuxIO_Print
|
|---|
| 106 | pop si
|
|---|
| 107 | ;~ call DEBUG_DumpRegisters
|
|---|
| 108 | ;~ call AuxIO_DumpParagraph
|
|---|
| 109 | ;~ call AuxIO_TeletypeNL
|
|---|
| 110 | popa
|
|---|
| 111 | popf
|
|---|
| 112 | ENDIF
|
|---|
| 113 | ENDIF
|
|---|
| 114 |
|
|---|
| 115 | mov ax, cs
|
|---|
| 116 | mov ds, ax
|
|---|
| 117 | mov es, ax ; Safety first (CS==DS==ES)
|
|---|
| 118 | ; --- Overwrite Floppy-Name with "FloppyDrive"
|
|---|
| 119 | mov si, offset TXT_Floppy_Drive
|
|---|
| 120 | mov di, offset PartitionTable
|
|---|
| 121 | sub di, 30 ; Adjust to Floppy-Name
|
|---|
| 122 | mov cx, 11
|
|---|
| 123 | rep movsb
|
|---|
| 124 | mov si, offset Configuration ; Calculate new checksum
|
|---|
| 125 | xor bx, bx
|
|---|
| 126 |
|
|---|
| 127 | ; Changed from 5 to calculated value (not here, see compat. issue below)
|
|---|
| 128 | ; Fixes issue: #2987 -- "air-boot doesn't remember drive letter"
|
|---|
| 129 | ; Size of the ab-configuration in 512 byte sectors
|
|---|
| 130 | ;mov cx, (MBR_BackUpMBR - Configuration) / 200h
|
|---|
| 131 |
|
|---|
| 132 | ; AB v1.07 stores a 5 sector configuration with a 5 sector checksum.
|
|---|
| 133 | ; AB v1.0.8+ *should* stores a 7 sector configuration with a
|
|---|
| 134 | ; 7 sector checksum.
|
|---|
| 135 | ; Because 5 was hardcoded here, SET(A)BOOT v1.07 will see see an AB v1.0.8+
|
|---|
| 136 | ; config as corrupted, while this is not the case.
|
|---|
| 137 | ; So, for compatibility reasons, in v1.0.8+, the checksum stored is over
|
|---|
| 138 | ; 5 sectors, to be compatible with v1.07.
|
|---|
| 139 | ; This may change (be corrected) in future versions !
|
|---|
| 140 | mov cx,5
|
|---|
| 141 |
|
|---|
| 142 | mov dx, [CFG_CheckConfig]
|
|---|
| 143 | mov [CFG_CheckConfig], bx
|
|---|
| 144 | DIOSC_Loop:
|
|---|
| 145 | call MBR_GetCheckOfSector
|
|---|
| 146 | loop DIOSC_Loop
|
|---|
| 147 | mov [CFG_CheckConfig], bx
|
|---|
| 148 | ; --------------------------------------------------------------------
|
|---|
| 149 | ; ES == CS
|
|---|
| 150 | mov bx, offset Configuration
|
|---|
| 151 | xor dh, dh
|
|---|
| 152 | mov dl, [BIOS_BootDisk] ; Disk we booted from
|
|---|
| 153 | mov cx, 0037h ; Sector 55 (CHS)
|
|---|
| 154 |
|
|---|
| 155 | ; Changed from 5 to calculated value
|
|---|
| 156 | ; Fixes issue: #2987 -- "air-boot doesn't remember drive letter"
|
|---|
| 157 | ; Size of the ab-configuration in 512 byte sectors
|
|---|
| 158 | mov al, (MBR_BackUpMBR - Configuration) / 200h
|
|---|
| 159 | mov ah,03h
|
|---|
| 160 |
|
|---|
| 161 | int 13h
|
|---|
| 162 | jnc DIOSC_NoError
|
|---|
| 163 | call MBR_SaveError ; Will Abort BootUp
|
|---|
| 164 | DIOSC_NoError:
|
|---|
| 165 | ret
|
|---|
| 166 | DriveIO_SaveConfiguration EndP
|
|---|
| 167 |
|
|---|
| 168 | DriveIO_UpdateFloppyName Proc Near Uses bx cx dx ds si es di
|
|---|
| 169 | mov ax, cs
|
|---|
| 170 | mov ds, ax
|
|---|
| 171 | mov es, ax
|
|---|
| 172 |
|
|---|
| 173 | mov ah, 00h ; Function 0 - Reset Drive
|
|---|
| 174 | xor dl, dl
|
|---|
| 175 | int 13h
|
|---|
| 176 | xor dx, dx ; Cylinder=0, Head=0
|
|---|
| 177 | mov cx, 1 ; Sector=1, Drive=0
|
|---|
| 178 | mov bx, offset TmpSector ; ES:BX - TmpSector
|
|---|
| 179 | mov ax, 0201h ; Function 2 - Load Sector
|
|---|
| 180 | int 13h
|
|---|
| 181 | jnc DIOUFN_AllFine
|
|---|
| 182 |
|
|---|
| 183 | ; --- Overwrite Floppy-Name with "No Disc"
|
|---|
| 184 | mov si, offset TXT_Floppy_NoDisc
|
|---|
| 185 | xor ax, ax
|
|---|
| 186 | DIOUFN_WriteFloppyName:
|
|---|
| 187 | mov di, offset PartitionTable
|
|---|
| 188 | sub di, 30 ; Adjust to Floppy-Name
|
|---|
| 189 | mov cl, 11
|
|---|
| 190 | rep movsb
|
|---|
| 191 | ret ; AX=-1 -> GotDisc, =0 -> NoDisc
|
|---|
| 192 |
|
|---|
| 193 | ; --- Floppy found and read, data in TempSector
|
|---|
| 194 | DIOUFN_AllFine:
|
|---|
| 195 | mov ax, -1
|
|---|
| 196 | mov si, offset TXT_Floppy_NoName
|
|---|
| 197 | cmp wptr es:[bx+54], 'AF'
|
|---|
| 198 | jne DIOUFN_WriteFloppyName
|
|---|
| 199 | cmp wptr es:[bx+56], '1T'
|
|---|
| 200 | jne DIOUFN_WriteFloppyName
|
|---|
| 201 | cmp bptr es:[bx+58], '2'
|
|---|
| 202 | jne DIOUFN_WriteFloppyName
|
|---|
| 203 | mov si, bx
|
|---|
| 204 | add si, 43 ; FAT12 - Volume Label Location
|
|---|
| 205 | jmp DIOUFN_WriteFloppyName
|
|---|
| 206 | DriveIO_UpdateFloppyName EndP
|
|---|
| 207 |
|
|---|
| 208 | ; =============================================================================
|
|---|
| 209 | ; HARDDRIVE / GENERAL ACCESS
|
|---|
| 210 | ; =============================================================================
|
|---|
| 211 | ; The following routines are used for harddisc/floppy access.
|
|---|
| 212 | ; The access is done via INT 13h/CHS or INT 13h/LBA.
|
|---|
| 213 | ; Access will be done prefered by INT 13h/CHS, because it's (I wonder!) much
|
|---|
| 214 | ; faster, than the LBA-method. I don't know, why LBA is so slow. Perhaps BIOS.
|
|---|
| 215 | ;
|
|---|
| 216 | ; Internal access (to AiR-BOOT) is always done via INT 13h/CHS.
|
|---|
| 217 |
|
|---|
| 218 | DriveIO_GetHardDriveCount Proc Near Uses ds si
|
|---|
| 219 | push ds
|
|---|
| 220 | push si
|
|---|
| 221 | push 0040h
|
|---|
| 222 | pop ds
|
|---|
| 223 | mov si, 0075h
|
|---|
| 224 | mov dh, ds:[si] ; 40:75 -> POST: Total Harddiscs == DL
|
|---|
| 225 | pop si
|
|---|
| 226 | pop ds
|
|---|
| 227 | mov [TotalHarddiscs], dh
|
|---|
| 228 | ret
|
|---|
| 229 | DriveIO_GetHardDriveCount EndP
|
|---|
| 230 |
|
|---|
| 231 |
|
|---|
| 232 | ; Fills our LBA-Usage table. It holds the LBA-address, where BIOS/CHS access is
|
|---|
| 233 | ; stopped and BIOS/LBA access is started.
|
|---|
| 234 | ; This is calculated by Sector*Heads. Comparing will get done with Bit 25-10
|
|---|
| 235 | ; on LBA sectors, so we actually divide sector number by 1024.
|
|---|
| 236 | DriveIO_InitLBASwitchTable Proc Near Uses es di
|
|---|
| 237 | mov di, offset LBASwitchTable
|
|---|
| 238 | mov dh, [TotalHarddiscs]
|
|---|
| 239 | mov dl, 80h ; First disk to process
|
|---|
| 240 | DIOILUT_DriveLoop:
|
|---|
| 241 | push dx
|
|---|
| 242 | push di
|
|---|
| 243 | mov ah, 08h
|
|---|
| 244 | int 13h ; DISK - GET DRIVE PARAMETERS
|
|---|
| 245 | mov ah, 0FBh ; Assume 255 heads/63 sectors, if error
|
|---|
| 246 | jc DIOILUT_Error
|
|---|
| 247 | and cl, 111111b ; Isolate lower 6 bits of CL -> sector count
|
|---|
| 248 |
|
|---|
| 249 | ;movzx ax, cl
|
|---|
| 250 | mov al,cl
|
|---|
| 251 | mov ah,0
|
|---|
| 252 |
|
|---|
| 253 | mov bl, dh ; DH -> max head number
|
|---|
| 254 | mul bl ; AX = Sectors*Heads
|
|---|
| 255 | shl ah, 1
|
|---|
| 256 | shl ah, 1 ; Shift 2 bits, so we are able to compare to
|
|---|
| 257 | ; bit 16-23 of the LBA address
|
|---|
| 258 | DIOILUT_Error:
|
|---|
| 259 | pop di
|
|---|
| 260 | pop dx
|
|---|
| 261 | mov bptr ds:[di], ah ; Save that value
|
|---|
| 262 | inc di ; Go to next BYTE
|
|---|
| 263 | inc dl ; Next disk
|
|---|
| 264 | dec dh ; Decrease disks to process
|
|---|
| 265 | jnz DIOILUT_DriveLoop ; Next disk if DH != 0
|
|---|
| 266 | ret
|
|---|
| 267 | DriveIO_InitLBASwitchTable EndP
|
|---|
| 268 |
|
|---|
| 269 |
|
|---|
| 270 |
|
|---|
| 271 |
|
|---|
| 272 | ;FIXME: Only LBA gets updated, need to update CHS too !!!!!!!
|
|---|
| 273 |
|
|---|
| 274 | ; Adjusts BX:AX / CX:DX to meet LVM sector location
|
|---|
| 275 | ; BX:AX / CX:DX point to MBR or EBR !
|
|---|
| 276 | ; Destroys SI
|
|---|
| 277 | ; Rousseau: Enhanced to handle sector-numbers 127 and 255 besides 63 for LVM-info sectors.
|
|---|
| 278 | ; Ugly, need to cleanup.
|
|---|
| 279 | DriveIO_LVMAdjustToInfoSector Proc Near
|
|---|
| 280 |
|
|---|
| 281 | IFDEF AUX_DEBUG
|
|---|
| 282 | IF 0
|
|---|
| 283 | pusha
|
|---|
| 284 | push si
|
|---|
| 285 | mov si, offset $+5
|
|---|
| 286 | jmp @F
|
|---|
| 287 | db 10,'DriveIO_LVMAdjustToInfoSector:',10,0
|
|---|
| 288 | @@:
|
|---|
| 289 | call AuxIO_Print
|
|---|
| 290 | pop si
|
|---|
| 291 | call DEBUG_DumpRegisters
|
|---|
| 292 | ;~ call AuxIO_DumpParagraph
|
|---|
| 293 | ;~ call AuxIO_TeletypeNL
|
|---|
| 294 | popa
|
|---|
| 295 | ENDIF
|
|---|
| 296 | ENDIF
|
|---|
| 297 |
|
|---|
| 298 | push cx ; Save Cyl/Sec part
|
|---|
| 299 | xor ch,ch ; Clear low Cyl part
|
|---|
| 300 | and cl,63 ; Clear high Cyl part
|
|---|
| 301 | push bx ; We need BX...
|
|---|
| 302 | push dx ; and DX temoraily
|
|---|
| 303 | mov bx,offset [TrueSecs] ; Offset of sector table
|
|---|
| 304 | xor dh,dh ; Clear DH because we use DL as index
|
|---|
| 305 | and dl,01111111b ; Remove high bit of BIOS disk-nr
|
|---|
| 306 | shl dx,2 ; Index to DWORD table
|
|---|
| 307 | add bx,dx ; Point to TrueSecs for this disk
|
|---|
| 308 | mov si,[bx] ; Get SPT for this disk
|
|---|
| 309 | pop dx ; Restore DX...
|
|---|
| 310 | pop bx ; and BX
|
|---|
| 311 | ;~ sub si,cx ; Adjust offset !! INCORRECT FOR LBA (TP CX != 0 !!)
|
|---|
| 312 | dec si
|
|---|
| 313 | pop cx ; Restore Cyl/Sec part
|
|---|
| 314 | add ax,si ; Add offset to low part...
|
|---|
| 315 | adc bx,0 ; and high part of LBA address
|
|---|
| 316 | or cl,63 ; Adjust CHS part !FIX ME for > 63! !! FIX HUGE DRIVE !!
|
|---|
| 317 |
|
|---|
| 318 | IFDEF AUX_DEBUG
|
|---|
| 319 | IF 0
|
|---|
| 320 | pusha
|
|---|
| 321 | push si
|
|---|
| 322 | mov si, offset $+5
|
|---|
| 323 | jmp @F
|
|---|
| 324 | db 10,'adjusted',10,0
|
|---|
| 325 | @@:
|
|---|
| 326 | call AuxIO_Print
|
|---|
| 327 | pop si
|
|---|
| 328 | call DEBUG_DumpRegisters
|
|---|
| 329 | ;~ call AuxIO_DumpParagraph
|
|---|
| 330 | ;~ call AuxIO_TeletypeNL
|
|---|
| 331 | popa
|
|---|
| 332 | ENDIF
|
|---|
| 333 | ENDIF
|
|---|
| 334 |
|
|---|
| 335 | ret
|
|---|
| 336 |
|
|---|
| 337 | DriveIO_LVMAdjustToInfoSector EndP
|
|---|
| 338 |
|
|---|
| 339 |
|
|---|
| 340 |
|
|---|
| 341 |
|
|---|
| 342 |
|
|---|
| 343 |
|
|---|
| 344 | ; #########################################################################
|
|---|
| 345 | ; Routine: Loads partition to ExecBase and checks for validity
|
|---|
| 346 | ; #########################################################################
|
|---|
| 347 | ; Calling : bx:ax - Absolute sector
|
|---|
| 348 | ; cx:dx - Cylinder/Sector, Side/Drive (hi/lo-byte)
|
|---|
| 349 | ; Returns : Carry Set if invalid partition encountered
|
|---|
| 350 | ; Preserve: all registers
|
|---|
| 351 | ; #########################################################################
|
|---|
| 352 | DriveIO_LoadPartition Proc Near Uses si
|
|---|
| 353 | mov wptr cs:[CurPartition_Location+0], ax
|
|---|
| 354 | mov wptr cs:[CurPartition_Location+2], bx
|
|---|
| 355 | mov wptr cs:[CurPartition_Location+4], dx
|
|---|
| 356 | mov wptr cs:[CurPartition_Location+6], cx ; Saves the location
|
|---|
| 357 | mov si, offset PartitionSector ; DS:SI - ExecBase
|
|---|
| 358 | call DriveIO_LoadSector
|
|---|
| 359 | clc
|
|---|
| 360 | cmp wptr [si+LocBR_Magic], 0AA55h
|
|---|
| 361 | je DIOLP_Success
|
|---|
| 362 | ; We check, if we are scanning partitions. In that case, if CHS is not 0/0/1
|
|---|
| 363 | ; we will display a "bad partition table" message and halt the system.
|
|---|
| 364 | cmp cx, 0001h
|
|---|
| 365 | jne DIOLP_Failed
|
|---|
| 366 | or dh, dh
|
|---|
| 367 | jnz DIOLP_Failed
|
|---|
| 368 | stc ; Set carry, so no partition table
|
|---|
| 369 | DIOLP_Success:
|
|---|
| 370 |
|
|---|
| 371 | IFDEF AUX_DEBUG
|
|---|
| 372 | ; show current partition location
|
|---|
| 373 | ;~ pushf
|
|---|
| 374 | ;~ pusha
|
|---|
| 375 | ;~ call AuxIO_TeletypeNL
|
|---|
| 376 | ;~ mov si,offset db_curpartloc
|
|---|
| 377 | ;~ call AuxIO_Print
|
|---|
| 378 | ;~ mov dx,word ptr [CurPartition_Location+02]
|
|---|
| 379 | ;~ mov ax,word ptr [CurPartition_Location+00]
|
|---|
| 380 | ;~ call AuxIO_TeletypeHexDWord
|
|---|
| 381 | ;~ call AuxIO_TeletypeNL
|
|---|
| 382 | ;~ mov si,offset PartitionSector
|
|---|
| 383 | ;~ call AuxIO_DumpSector
|
|---|
| 384 | ;~ call AuxIO_TeletypeNL
|
|---|
| 385 | ;~ popa
|
|---|
| 386 | ;~ popf
|
|---|
| 387 | ENDIF
|
|---|
| 388 |
|
|---|
| 389 | ret
|
|---|
| 390 | DIOLP_Failed:
|
|---|
| 391 | jmp DriveIO_GotLoadError
|
|---|
| 392 | DriveIO_LoadPartition EndP
|
|---|
| 393 |
|
|---|
| 394 | ; #########################################################################
|
|---|
| 395 | ; Routine: Writes a partition from ExecBase to its original sector
|
|---|
| 396 | ; #########################################################################
|
|---|
| 397 | ; Calling : none
|
|---|
| 398 | ; Returns : none
|
|---|
| 399 | ; Preserve: all registers
|
|---|
| 400 | ; #########################################################################
|
|---|
| 401 | DriveIO_SavePartition Proc Near Uses ax bx cx dx si
|
|---|
| 402 |
|
|---|
| 403 | IFDEF AUX_DEBUG
|
|---|
| 404 | IF 0
|
|---|
| 405 | pushf
|
|---|
| 406 | pusha
|
|---|
| 407 | push si
|
|---|
| 408 | mov si, offset $+5
|
|---|
| 409 | jmp @F
|
|---|
| 410 | db 10,'DriveIO_SavePartition:',10,0
|
|---|
| 411 | @@:
|
|---|
| 412 | call AuxIO_Print
|
|---|
| 413 | pop si
|
|---|
| 414 | ;~ call DEBUG_DumpRegisters
|
|---|
| 415 | ;~ call AuxIO_DumpParagraph
|
|---|
| 416 | ;~ call AuxIO_TeletypeNL
|
|---|
| 417 | popa
|
|---|
| 418 | popf
|
|---|
| 419 | ENDIF
|
|---|
| 420 | ENDIF
|
|---|
| 421 |
|
|---|
| 422 | mov ax, wptr cs:[CurPartition_Location+0]
|
|---|
| 423 | mov bx, wptr cs:[CurPartition_Location+2]
|
|---|
| 424 | mov dx, wptr cs:[CurPartition_Location+4]
|
|---|
| 425 | mov cx, wptr cs:[CurPartition_Location+6] ; Gets prev. saved location
|
|---|
| 426 | mov si, offset PartitionSector ; DS:SI - ExecBase
|
|---|
| 427 | cmp wptr [si+LocBR_Magic], 0AA55h ; Checks for signature, if not found
|
|---|
| 428 | jne DIOSP_SevereError ; we assume a really bad error
|
|---|
| 429 | call DriveIO_SaveSector
|
|---|
| 430 | DIOSP_SevereError:
|
|---|
| 431 | ret
|
|---|
| 432 | DriveIO_SavePartition EndP
|
|---|
| 433 |
|
|---|
| 434 | ; Keeps DS:SI for caller
|
|---|
| 435 | DriveIO_LoadTmpSector Proc Near
|
|---|
| 436 | mov si, offset TmpSector
|
|---|
| 437 | call DriveIO_LoadSector
|
|---|
| 438 | ret
|
|---|
| 439 | DriveIO_LoadTmpSector EndP
|
|---|
| 440 |
|
|---|
| 441 | ; Keeps DS:SI for caller
|
|---|
| 442 | DriveIO_SaveTmpSector Proc Near
|
|---|
| 443 | mov si, offset TmpSector
|
|---|
| 444 | call DriveIO_SaveSector
|
|---|
| 445 | ret
|
|---|
| 446 | DriveIO_SaveTmpSector EndP
|
|---|
| 447 |
|
|---|
| 448 |
|
|---|
| 449 |
|
|---|
| 450 | ; Keeps DS:SI for caller, sets carry if valid LVM sector encountered
|
|---|
| 451 | DriveIO_LoadLVMSector Proc Near Uses ax bx cx dx
|
|---|
| 452 |
|
|---|
| 453 | IFDEF AUX_DEBUG
|
|---|
| 454 | IF 0
|
|---|
| 455 | pushf
|
|---|
| 456 | pusha
|
|---|
| 457 | push si
|
|---|
| 458 | mov si, offset $+5
|
|---|
| 459 | jmp @F
|
|---|
| 460 | db 10,'DriveIO_LoadLVMSector:',10,0
|
|---|
| 461 | @@:
|
|---|
| 462 | call AuxIO_Print
|
|---|
| 463 | pop si
|
|---|
| 464 | ;~ call DEBUG_DumpRegisters
|
|---|
| 465 | ;~ call AuxIO_DumpParagraph
|
|---|
| 466 | ;~ call AuxIO_TeletypeNL
|
|---|
| 467 | popa
|
|---|
| 468 | popf
|
|---|
| 469 | ENDIF
|
|---|
| 470 | ENDIF
|
|---|
| 471 |
|
|---|
| 472 | test byte ptr [CFG_IgnoreLVM], 1 ; We are supposed to ignore LVM, so
|
|---|
| 473 | jnz DIOLLVMS_NoLVMSector ; don't load but declare as bad!
|
|---|
| 474 | mov ax, wptr cs:[CurPartition_Location+0]
|
|---|
| 475 | mov bx, wptr cs:[CurPartition_Location+2]
|
|---|
| 476 | mov dx, wptr cs:[CurPartition_Location+4]
|
|---|
| 477 | mov cx, wptr cs:[CurPartition_Location+6] ; Gets cur. partition location
|
|---|
| 478 |
|
|---|
| 479 | call DriveIO_LVMAdjustToInfoSector
|
|---|
| 480 |
|
|---|
| 481 | mov si, offset LVMSector
|
|---|
| 482 | call DriveIO_LoadSector
|
|---|
| 483 |
|
|---|
| 484 | IFDEF AUX_DEBUG
|
|---|
| 485 | ; show current partition location
|
|---|
| 486 | ;~ pushf
|
|---|
| 487 | ;~ pusha
|
|---|
| 488 | ;~ call AuxIO_TeletypeNL
|
|---|
| 489 | ;~ mov si,offset db_curlvmsec
|
|---|
| 490 | ;~ call AuxIO_Print
|
|---|
| 491 | ;~ mov dx,bx
|
|---|
| 492 | ;~ call AuxIO_TeletypeHexDWord
|
|---|
| 493 | ;~ call AuxIO_TeletypeNL
|
|---|
| 494 | ;~ mov si,offset LVMSector
|
|---|
| 495 | ;~ call AuxIO_DumpSector
|
|---|
| 496 | ;~ call AuxIO_TeletypeNL
|
|---|
| 497 | ;~ popa
|
|---|
| 498 | ;~ popf
|
|---|
| 499 | ENDIF
|
|---|
| 500 |
|
|---|
| 501 | call LVM_CheckSectorSignature
|
|---|
| 502 | jnc DIOLLVMS_NoLVMSector
|
|---|
| 503 | call LVM_CheckSectorCRC
|
|---|
| 504 | jnc DIOLLVMS_NoLVMSector
|
|---|
| 505 | ret
|
|---|
| 506 | ; This here is called, if an invalid (or no) LVM information sector is found
|
|---|
| 507 | ; It will truncate the first byte of the sector, so all other routines
|
|---|
| 508 | ; will notice it easily by just comparing the first byte.
|
|---|
| 509 | DIOLLVMS_NoLVMSector:
|
|---|
| 510 | mov bptr [si+LocLVM_SignatureStart], 0
|
|---|
| 511 | ret
|
|---|
| 512 | DriveIO_LoadLVMSector EndP
|
|---|
| 513 |
|
|---|
| 514 |
|
|---|
| 515 |
|
|---|
| 516 | ; Keeps DS:SI for caller, saves at anytime w/o checks (!)
|
|---|
| 517 | DriveIO_SaveLVMSector Proc Near Uses ax bx cx dx
|
|---|
| 518 |
|
|---|
| 519 | IFDEF AUX_DEBUG
|
|---|
| 520 | IF 0
|
|---|
| 521 | pushf
|
|---|
| 522 | pusha
|
|---|
| 523 | push si
|
|---|
| 524 | mov si, offset $+5
|
|---|
| 525 | jmp @F
|
|---|
| 526 | db 10,'DriveIO_SaveLVMSector:',10,0
|
|---|
| 527 | @@:
|
|---|
| 528 | call AuxIO_Print
|
|---|
| 529 | pop si
|
|---|
| 530 | ;~ call DEBUG_DumpRegisters
|
|---|
| 531 | ;~ call AuxIO_DumpParagraph
|
|---|
| 532 | ;~ call AuxIO_TeletypeNL
|
|---|
| 533 | popa
|
|---|
| 534 | popf
|
|---|
| 535 | ENDIF
|
|---|
| 536 | ENDIF
|
|---|
| 537 |
|
|---|
| 538 | test byte ptr [CFG_IgnoreLVM], 1 ; We are supposed to ignore LVM, so
|
|---|
| 539 | jnz DIOSLVMS_SevereError ; don't save at anytime (security!)
|
|---|
| 540 | mov ax, wptr cs:[CurPartition_Location+0]
|
|---|
| 541 | mov bx, wptr cs:[CurPartition_Location+2]
|
|---|
| 542 | mov dx, wptr cs:[CurPartition_Location+4]
|
|---|
| 543 | mov cx, wptr cs:[CurPartition_Location+6] ; Gets cur. partition location
|
|---|
| 544 | call LVM_CheckSectorSignature
|
|---|
| 545 | jnc DIOSLVMS_SevereError ; LVM Signature must be there
|
|---|
| 546 |
|
|---|
| 547 | IFDEF AUX_DEBUG
|
|---|
| 548 | ;~ dioatlvm db 'DriveIO_LVMAdjustToInfoSector',10,0
|
|---|
| 549 | ;~ pushf
|
|---|
| 550 | ;~ pusha
|
|---|
| 551 | ;~ mov si,offset dioatlvm
|
|---|
| 552 | ;~ call AuxIO_Print
|
|---|
| 553 | ;~ popa
|
|---|
| 554 | ;~ popf
|
|---|
| 555 | call DEBUG_DumpRegisters
|
|---|
| 556 | call DEBUG_DumpCHS
|
|---|
| 557 | ENDIF
|
|---|
| 558 |
|
|---|
| 559 | call DriveIO_LVMAdjustToInfoSector
|
|---|
| 560 |
|
|---|
| 561 | IFDEF AUX_DEBUG
|
|---|
| 562 | call DEBUG_DumpRegisters
|
|---|
| 563 | call DEBUG_DumpCHS
|
|---|
| 564 | ENDIF
|
|---|
| 565 |
|
|---|
| 566 | mov si, offset LVMSector
|
|---|
| 567 | call DriveIO_SaveSector
|
|---|
| 568 | DIOSLVMS_SevereError:
|
|---|
| 569 | ret
|
|---|
| 570 | DriveIO_SaveLVMSector EndP
|
|---|
| 571 |
|
|---|
| 572 |
|
|---|
| 573 |
|
|---|
| 574 | ; Special error message instead of "LOAD ERROR" during partition scanning,
|
|---|
| 575 | ; so users will notice that something is bad with their partition table(s)
|
|---|
| 576 | DriveIO_GotLoadError Proc Near
|
|---|
| 577 | test byte ptr cs:[CurIO_Scanning], 1 ; Must be CS:, cause DS!=CS maybe here
|
|---|
| 578 | jnz InScanMode
|
|---|
| 579 | jmp MBR_LoadError
|
|---|
| 580 | InScanMode:
|
|---|
| 581 | mov si, offset TXT_BrokenPartitionTable
|
|---|
| 582 | push cs
|
|---|
| 583 | pop ds
|
|---|
| 584 | call MBR_Teletype
|
|---|
| 585 | mov si, offset BrokenHDD
|
|---|
| 586 | sub dl, 50h ; 80h -> '0'
|
|---|
| 587 | cmp dl, 39h
|
|---|
| 588 | jbe DIOGLE_BelowA
|
|---|
| 589 | add dl, 7 ; 3Ah -> 'A'
|
|---|
| 590 | DIOGLE_BelowA:
|
|---|
| 591 | mov bptr [si+5], dl
|
|---|
| 592 | call MBR_Teletype
|
|---|
| 593 |
|
|---|
| 594 | ; JWasm: cannot jump to local label in other procedure.
|
|---|
| 595 | ; Changed to halt here.
|
|---|
| 596 | ;jmp MBRLE_Halt
|
|---|
| 597 | DriveIO_GotLoadError_halt:
|
|---|
| 598 | jmp DriveIO_GotLoadError_halt
|
|---|
| 599 | DriveIO_GotLoadError EndP
|
|---|
| 600 |
|
|---|
| 601 | ; #########################################################################
|
|---|
| 602 | ; Routine: Loads a specified sector to DS:DI
|
|---|
| 603 | ; #########################################################################
|
|---|
| 604 | ; Calling : bx:ax - Absolute sector
|
|---|
| 605 | ; cx:dx - Cylinder/Sector, Side/Drive (hi/lo-byte)
|
|---|
| 606 | ; ds:si - Destination-Adress
|
|---|
| 607 | ; Returns : none
|
|---|
| 608 | ; Preserve: all registers
|
|---|
| 609 | ; #########################################################################
|
|---|
| 610 | DriveIO_LoadSector Proc Near Uses ax bx cx dx ds si es di
|
|---|
| 611 |
|
|---|
| 612 | IFDEF AUX_DEBUG
|
|---|
| 613 | IF 0
|
|---|
| 614 | pushf
|
|---|
| 615 | pusha
|
|---|
| 616 | push si
|
|---|
| 617 | mov si, offset $+5
|
|---|
| 618 | jmp @F
|
|---|
| 619 | db 10,'DriveIO_LoadSector:',10,0
|
|---|
| 620 | @@:
|
|---|
| 621 | call AuxIO_Print
|
|---|
| 622 | pop si
|
|---|
| 623 | ;~ call DEBUG_DumpRegisters
|
|---|
| 624 | ;~ call AuxIO_DumpParagraph
|
|---|
| 625 | ;~ call AuxIO_TeletypeNL
|
|---|
| 626 | popa
|
|---|
| 627 | popf
|
|---|
| 628 | ENDIF
|
|---|
| 629 | ENDIF
|
|---|
| 630 |
|
|---|
| 631 | ; Is the drive not a harddrive?
|
|---|
| 632 | cmp dl, 80h
|
|---|
| 633 | jb DIOLS_UseNormal
|
|---|
| 634 |
|
|---|
| 635 | test byte ptr cs:[CurIO_UseExtension], 1
|
|---|
| 636 | jz DIOLS_UseNormal
|
|---|
| 637 | ; Are we forced do use LBA via Setting?
|
|---|
| 638 | jnz DIOLS_UseExtension
|
|---|
| 639 |
|
|---|
| 640 | ; Upper 8 bits of LBA-address set?
|
|---|
| 641 | ; Then use LBA (maximum boundary is 16320x16x63 = FB0400h)
|
|---|
| 642 | or bh, bh
|
|---|
| 643 | jnz DIOLS_UseExtension
|
|---|
| 644 | ; Compare Switch-Table value to bit 16-23 of LBA-address
|
|---|
| 645 | mov di, dx
|
|---|
| 646 | and di, 007Fh
|
|---|
| 647 | cmp bptr cs:[LBASwitchTable+di], bl
|
|---|
| 648 | jbe DIOLS_UseExtension
|
|---|
| 649 |
|
|---|
| 650 | DIOLS_UseNormal:
|
|---|
| 651 |
|
|---|
| 652 | IFDEF AUX_DEBUG
|
|---|
| 653 | IF 0
|
|---|
| 654 | pusha
|
|---|
| 655 | push si
|
|---|
| 656 | mov si, offset $+5
|
|---|
| 657 | jmp @F
|
|---|
| 658 | db 10,'DriveIO_ReadSectorCHS:',10,0
|
|---|
| 659 | @@:
|
|---|
| 660 | call AuxIO_Print
|
|---|
| 661 | pop si
|
|---|
| 662 | call DEBUG_DumpRegisters
|
|---|
| 663 | call AuxIO_DumpParagraph
|
|---|
| 664 | call AuxIO_TeletypeNL
|
|---|
| 665 | popa
|
|---|
| 666 | ENDIF
|
|---|
| 667 | ENDIF
|
|---|
| 668 |
|
|---|
| 669 | mov di, 3 ; retry count
|
|---|
| 670 | DIOLS_ErrorLoop:
|
|---|
| 671 | push ds
|
|---|
| 672 | pop es
|
|---|
| 673 | mov bx, si ; ES:BX - Destination
|
|---|
| 674 | mov ax, 0201h ; Function 2 - Load Sector
|
|---|
| 675 | int 13h
|
|---|
| 676 | jnc DIOLS_Success
|
|---|
| 677 | dec di ; decrement retry count
|
|---|
| 678 | jnz DIOLS_ErrorLoop
|
|---|
| 679 |
|
|---|
| 680 | ; Sector load failed...
|
|---|
| 681 | jmp DriveIO_GotLoadError
|
|---|
| 682 |
|
|---|
| 683 | DIOLS_UseExtension:
|
|---|
| 684 |
|
|---|
| 685 | mov di, ds ; segment for transfer address
|
|---|
| 686 | mov cx, ax ; low word of lba
|
|---|
| 687 | call DriveIO_ReadSectorLBA ; extended read
|
|---|
| 688 | jc DriveIO_GotLoadError ; halt on error
|
|---|
| 689 |
|
|---|
| 690 | ;~ push cx
|
|---|
| 691 | ;~ mov cs:[INT13X_DAP_NumBlocks], 1 ; Copy ONE sector
|
|---|
| 692 | ;~ mov wptr cs:[INT13X_DAP_Transfer+0], si
|
|---|
| 693 | ;~ mov cx, ds
|
|---|
| 694 | ;~ mov wptr cs:[INT13X_DAP_Transfer+2], cx ; Fill out Transfer Adress
|
|---|
| 695 | ;~ mov wptr cs:[INT13X_DAP_Absolute+0], ax
|
|---|
| 696 | ;~ mov wptr cs:[INT13X_DAP_Absolute+2], bx ; Fill out Absolute Sector
|
|---|
| 697 | ;~ push cs
|
|---|
| 698 | ;~ pop ds
|
|---|
| 699 | ;~ mov si, offset [INT13X_DAP]
|
|---|
| 700 | ;~ mov ah, 42h ; Extended Read
|
|---|
| 701 | ;~ int 13h
|
|---|
| 702 | ;~ pop cx
|
|---|
| 703 | ;~ jnc DIOLS_Success
|
|---|
| 704 |
|
|---|
| 705 | ; Sector load failed...
|
|---|
| 706 | ;~ jmp DriveIO_GotLoadError
|
|---|
| 707 |
|
|---|
| 708 | DIOLS_Success:
|
|---|
| 709 | ret
|
|---|
| 710 | DriveIO_LoadSector EndP
|
|---|
| 711 |
|
|---|
| 712 |
|
|---|
| 713 |
|
|---|
| 714 | ;##############################################################################
|
|---|
| 715 | ;# ACTION : Reads a sector from disk using INT13 extensions
|
|---|
| 716 | ;# ----------------------------------------------------------------------------
|
|---|
| 717 | ;# IN : BX:CX - LBA address of sector
|
|---|
| 718 | ;# : DI:SI - SEG:OFF of transfer buffer
|
|---|
| 719 | ;# ----------------------------------------------------------------------------
|
|---|
| 720 | ;# OUT : CF=1 - failure, AH failure code
|
|---|
| 721 | ;# ----------------------------------------------------------------------------
|
|---|
| 722 | ;# EFFECTS : Modifies DAP structure and fills transfer buffer
|
|---|
| 723 | ;##############################################################################
|
|---|
| 724 | DriveIO_ReadSectorLBA Proc Near Uses bx cx dx si di ds es
|
|---|
| 725 |
|
|---|
| 726 | IFDEF AUX_DEBUG
|
|---|
| 727 | IF 0
|
|---|
| 728 | pushf
|
|---|
| 729 | pusha
|
|---|
| 730 | push si
|
|---|
| 731 | mov si, offset $+5
|
|---|
| 732 | jmp @F
|
|---|
| 733 | db 10,'DriveIO_ReadSectorLBA:',10,0
|
|---|
| 734 | @@:
|
|---|
| 735 | call AuxIO_Print
|
|---|
| 736 | pop si
|
|---|
| 737 | call DEBUG_DumpRegisters
|
|---|
| 738 | call AuxIO_DumpParagraph
|
|---|
| 739 | call AuxIO_TeletypeNL
|
|---|
| 740 | popa
|
|---|
| 741 | popf
|
|---|
| 742 | ENDIF
|
|---|
| 743 | ENDIF
|
|---|
| 744 |
|
|---|
| 745 | ; One sector to read
|
|---|
| 746 | mov cs:[INT13X_DAP_NumBlocks], 1
|
|---|
| 747 |
|
|---|
| 748 | ; Setup transfer address
|
|---|
| 749 | mov wptr cs:[INT13X_DAP_Transfer+0], si ; offset
|
|---|
| 750 | mov wptr cs:[INT13X_DAP_Transfer+2], di ; segment
|
|---|
| 751 |
|
|---|
| 752 | ; Setup LBA64 address of requested sector
|
|---|
| 753 | mov wptr cs:[INT13X_DAP_Absolute+0], cx ; low word lower part
|
|---|
| 754 | mov wptr cs:[INT13X_DAP_Absolute+2], bx ; high word lower part
|
|---|
| 755 | mov wptr cs:[INT13X_DAP_Absolute+4], 0 ; low word upper part
|
|---|
| 756 | mov wptr cs:[INT13X_DAP_Absolute+6], 0 ; high word upper part
|
|---|
| 757 |
|
|---|
| 758 | ; Address of packet
|
|---|
| 759 | mov si, offset [INT13X_DAP] ; disk address packet
|
|---|
| 760 |
|
|---|
| 761 | ; Do the extended read
|
|---|
| 762 | mov ah, 42h ; read function
|
|---|
| 763 | int 13h ; transfer to bios
|
|---|
| 764 |
|
|---|
| 765 | ; Error occured
|
|---|
| 766 | jc DriveIO_ReadSectorLBA_exit
|
|---|
| 767 |
|
|---|
| 768 | ; AH should also be zero
|
|---|
| 769 | test ah, ah
|
|---|
| 770 | stc
|
|---|
| 771 | jnz DriveIO_ReadSectorLBA_exit
|
|---|
| 772 |
|
|---|
| 773 | ; Disk read succeeded, clear CF
|
|---|
| 774 | clc
|
|---|
| 775 |
|
|---|
| 776 | DriveIO_ReadSectorLBA_exit:
|
|---|
| 777 | ret
|
|---|
| 778 |
|
|---|
| 779 | DriveIO_ReadSectorLBA EndP
|
|---|
| 780 |
|
|---|
| 781 |
|
|---|
| 782 |
|
|---|
| 783 | ;##############################################################################
|
|---|
| 784 | ;# ACTION : Writes a sector to disk using INT13 extensions
|
|---|
| 785 | ;# ----------------------------------------------------------------------------
|
|---|
| 786 | ;# IN : AL - write flags, AL.0 verify (1.0,2.0), AL.1 verify (2.1+)
|
|---|
| 787 | ;# : BX:CX - LBA address of sector
|
|---|
| 788 | ;# : DI:SI - SEG:OFF of transfer buffer
|
|---|
| 789 | ;# ----------------------------------------------------------------------------
|
|---|
| 790 | ;# OUT : CF=1 - failure, AH failure code
|
|---|
| 791 | ;# ----------------------------------------------------------------------------
|
|---|
| 792 | ;# EFFECTS : Modifies DAP structure and mofifies the disk
|
|---|
| 793 | ;##############################################################################
|
|---|
| 794 | DriveIO_WriteSectorLBA Proc Near Uses bx cx dx si di ds es
|
|---|
| 795 |
|
|---|
| 796 | IFDEF AUX_DEBUG
|
|---|
| 797 | IF 0
|
|---|
| 798 | pusha
|
|---|
| 799 | push si
|
|---|
| 800 | mov si, offset $+5
|
|---|
| 801 | jmp @F
|
|---|
| 802 | db 10,'DriveIO_WriteSectorLBA:',10,0
|
|---|
| 803 | @@:
|
|---|
| 804 | call AuxIO_Print
|
|---|
| 805 | pop si
|
|---|
| 806 | call DEBUG_DumpRegisters
|
|---|
| 807 | call AuxIO_DumpParagraph
|
|---|
| 808 | call AuxIO_TeletypeNL
|
|---|
| 809 | popa
|
|---|
| 810 | ENDIF
|
|---|
| 811 | ENDIF
|
|---|
| 812 |
|
|---|
| 813 | ; Mask reserved bits for write flags -- should check version here
|
|---|
| 814 | and al, 03h
|
|---|
| 815 |
|
|---|
| 816 | ; Actually, force 'no-write-verify' for now...
|
|---|
| 817 | xor al, al
|
|---|
| 818 |
|
|---|
| 819 | ; One sector to read
|
|---|
| 820 | mov cs:[INT13X_DAP_NumBlocks], 1
|
|---|
| 821 |
|
|---|
| 822 | ; Setup transfer address
|
|---|
| 823 | mov wptr cs:[INT13X_DAP_Transfer+0], si ; offset
|
|---|
| 824 | mov wptr cs:[INT13X_DAP_Transfer+2], di ; segment
|
|---|
| 825 |
|
|---|
| 826 | ; Setup LBA64 address of requested sector
|
|---|
| 827 | mov wptr cs:[INT13X_DAP_Absolute+0], cx ; low word lower part
|
|---|
| 828 | mov wptr cs:[INT13X_DAP_Absolute+2], bx ; high word lower part
|
|---|
| 829 | mov wptr cs:[INT13X_DAP_Absolute+4], 0 ; low word upper part
|
|---|
| 830 | mov wptr cs:[INT13X_DAP_Absolute+6], 0 ; high word upper part
|
|---|
| 831 |
|
|---|
| 832 | ; Address of packet
|
|---|
| 833 | mov si, offset [INT13X_DAP] ; disk address packet
|
|---|
| 834 |
|
|---|
| 835 | ; Do the extended write
|
|---|
| 836 | mov ah, 43h ; write function
|
|---|
| 837 | int 13h ; transfer to bios
|
|---|
| 838 |
|
|---|
| 839 | ; Error occured
|
|---|
| 840 | jc DriveIO_WriteSectorLBA_exit
|
|---|
| 841 |
|
|---|
| 842 | ; AH should also be zero
|
|---|
| 843 | test ah, ah
|
|---|
| 844 | stc
|
|---|
| 845 | jnz DriveIO_WriteSectorLBA_exit
|
|---|
| 846 |
|
|---|
| 847 | ; Disk write succeeded, clear CF
|
|---|
| 848 | clc
|
|---|
| 849 |
|
|---|
| 850 | DriveIO_WriteSectorLBA_exit:
|
|---|
| 851 | ret
|
|---|
| 852 |
|
|---|
| 853 | DriveIO_WriteSectorLBA EndP
|
|---|
| 854 |
|
|---|
| 855 |
|
|---|
| 856 |
|
|---|
| 857 | ;
|
|---|
| 858 | ; ############################################################
|
|---|
| 859 | ; # Check for a valid MBR-sector to be written to disk #
|
|---|
| 860 | ; ############################################################
|
|---|
| 861 | ;
|
|---|
| 862 | ; In
|
|---|
| 863 | ; --
|
|---|
| 864 | ; DL = Physical Disk
|
|---|
| 865 | ; BX:CX = LBA sector
|
|---|
| 866 | ; DI:SI = Source buffer
|
|---|
| 867 | ;
|
|---|
| 868 | ; Out
|
|---|
| 869 | ; ---
|
|---|
| 870 | ; CY = 1 if invalid MBR in source buffer, 0 if valid
|
|---|
| 871 | ;
|
|---|
| 872 | ; This routine is called when DriveIO_SaveSector attempts to write to the MBR.
|
|---|
| 873 | ; It checks if the sector to be written has some sensible values in certain
|
|---|
| 874 | ; places. In fact, if the sector is written to the boot-disk, the AiR-BOOT
|
|---|
| 875 | ; signature should be present and the partition table should be the same
|
|---|
| 876 | ; as the one at the start of the AiR-BOOT code in memory, except maybe for the
|
|---|
| 877 | ; active flags.
|
|---|
| 878 | ; For other disks, only the active flags are checked to be 00h or 80h and
|
|---|
| 879 | ; the AA55h MBR signature.
|
|---|
| 880 | ;
|
|---|
| 881 | DriveIO_ProtectMBR Proc Near
|
|---|
| 882 | pusha ; Push all registers
|
|---|
| 883 | push es ; Push ES because we need it for string instructions
|
|---|
| 884 | push cs ; Make ES point...
|
|---|
| 885 | pop es ; to CS
|
|---|
| 886 |
|
|---|
| 887 | ; Save the pointer to the sector to write in BX
|
|---|
| 888 | mov bx,si
|
|---|
| 889 |
|
|---|
| 890 | ;
|
|---|
| 891 | ; If the sector to be written is not the boot-disk, then skip
|
|---|
| 892 | ; checking the AiR-BOOT MBR.
|
|---|
| 893 | ;
|
|---|
| 894 | cmp dl, [BIOS_BootDisk]
|
|---|
| 895 | jne DriveIO_ProtectMBR_is_not_bootdisk
|
|---|
| 896 |
|
|---|
| 897 | ;
|
|---|
| 898 | ; The boot-disk is accessed so the sector to be written must be
|
|---|
| 899 | ; the AiR-BOOT MBR. This is the same as the first 512 bytes
|
|---|
| 900 | ; relocated to 8000:0000 and this the start of the AB-code.
|
|---|
| 901 | ;
|
|---|
| 902 | mov si,bx ; Get pointer to sector to write
|
|---|
| 903 | xor di,di ; Point DI to start of AB-code (MBR)
|
|---|
| 904 | mov cx, offset [MBR_PartTable] ; Bytes upto P-table must be same
|
|---|
| 905 | cld ; Compare upwards
|
|---|
| 906 | repe cmpsb ; Compare upto P-table
|
|---|
| 907 |
|
|---|
| 908 | ; If not the same this is not the an AiR-BOOT boot-disk MBR !
|
|---|
| 909 | jne DriveIO_ProtectMBR_not_valid_MBR ; SEVERE ERROR !
|
|---|
| 910 |
|
|---|
| 911 | ; Continue with signature check
|
|---|
| 912 | jmp DriveIO_ProtectMBR_check_signature
|
|---|
| 913 |
|
|---|
| 914 |
|
|---|
| 915 | ;
|
|---|
| 916 | ; The disk is not the boot-disk so we don't know what kind of MBR is on it.
|
|---|
| 917 | ; Some sanity checks should be here.
|
|---|
| 918 | ;
|
|---|
| 919 | DriveIO_ProtectMBR_is_not_bootdisk:
|
|---|
| 920 |
|
|---|
| 921 | ;
|
|---|
| 922 | ; sanity checks...
|
|---|
| 923 | ;
|
|---|
| 924 |
|
|---|
| 925 | ; Continue with signature check
|
|---|
| 926 | jmp DriveIO_ProtectMBR_check_signature
|
|---|
| 927 |
|
|---|
| 928 |
|
|---|
| 929 | DriveIO_ProtectMBR_check_signature:
|
|---|
| 930 | ; See if the sector to write contains a valid signature
|
|---|
| 931 | mov si,bx ; Get pointer to sector to write
|
|---|
| 932 | mov di, offset [MBR_Sig] ; Offset to MBR signature
|
|---|
| 933 | add si,di ; Make SI point to it in sec to write
|
|---|
| 934 | lodsw ; Load it
|
|---|
| 935 | cmp ax,0aa55h ; See if it is valid
|
|---|
| 936 |
|
|---|
| 937 | ; If no signature this cannot be a valid MBR !
|
|---|
| 938 | jne DriveIO_ProtectMBR_not_valid_MBR ; SEVERE ERROR !
|
|---|
| 939 |
|
|---|
| 940 |
|
|---|
| 941 | ;
|
|---|
| 942 | ; The sector to be written seems to be valid.
|
|---|
| 943 | ; Set CY=0 to indicate a valid MBR.
|
|---|
| 944 | ;
|
|---|
| 945 | DriveIO_ProtectMBR_is_valid_MBR:
|
|---|
| 946 | clc
|
|---|
| 947 | jmp DriveIO_ProtectMBR_end
|
|---|
| 948 |
|
|---|
| 949 | ;
|
|---|
| 950 | ; Something is terribly wrong; a non-MBR sector seems about to be written.
|
|---|
| 951 | ; Set CY=1 and let the calling code handle this situation.
|
|---|
| 952 | ;
|
|---|
| 953 | DriveIO_ProtectMBR_not_valid_MBR:
|
|---|
| 954 | stc
|
|---|
| 955 | jmp DriveIO_ProtectMBR_end
|
|---|
| 956 |
|
|---|
| 957 | ;
|
|---|
| 958 | ; Return to the caller with no registers modyfied except FLAGS.
|
|---|
| 959 | ;
|
|---|
| 960 | DriveIO_ProtectMBR_end:
|
|---|
| 961 | pop es
|
|---|
| 962 | popa
|
|---|
| 963 | ret
|
|---|
| 964 | DriveIO_ProtectMBR Endp
|
|---|
| 965 |
|
|---|
| 966 |
|
|---|
| 967 |
|
|---|
| 968 | ; #########################################################################
|
|---|
| 969 | ; Routine: Checks if the MBR is addressed by either CHS or LBA
|
|---|
| 970 | ; #########################################################################
|
|---|
| 971 | ; Calling : bx:ax - Absolute sector
|
|---|
| 972 | ; cx:dx - Cylinder/Sector, Side/Drive (hi/lo-byte)
|
|---|
| 973 | ; Returns : ZF=1 if MBR is addressed, else ZF=0
|
|---|
| 974 | ; Preserve: all registers
|
|---|
| 975 | ; #########################################################################
|
|---|
| 976 | DriveIO_MBR_Addressed Proc
|
|---|
| 977 | push ax
|
|---|
| 978 | push bx
|
|---|
| 979 |
|
|---|
| 980 | or bx,ax ; Results in 0 in BX if MBR is addressed by LBA
|
|---|
| 981 | jz DriveIO_MBR_Addressed_done
|
|---|
| 982 |
|
|---|
| 983 | mov ax,cx ; Results in 1 in AX if CYL 0, SEC 1 is addressed
|
|---|
| 984 | add al,dh ; Results in 1 in AX if HEAD 0 is addressed
|
|---|
| 985 | dec ax ; Results in 0 in AX if MBR is addressed by CHS
|
|---|
| 986 |
|
|---|
| 987 | DriveIO_MBR_Addressed_done:
|
|---|
| 988 | pop bx
|
|---|
| 989 | pop ax
|
|---|
| 990 | ret
|
|---|
| 991 | DriveIO_MBR_Addressed EndP
|
|---|
| 992 |
|
|---|
| 993 |
|
|---|
| 994 |
|
|---|
| 995 |
|
|---|
| 996 | ; #########################################################################
|
|---|
| 997 | ; Routine: Writes DS:SI to a specified sector
|
|---|
| 998 | ; #########################################################################
|
|---|
| 999 | ; Calling : bx:ax - Absolute sector
|
|---|
| 1000 | ; cx:dx - Cylinder/Sector, Side/Drive (hi/lo-byte)
|
|---|
| 1001 | ; ds:si - Source-Adress
|
|---|
| 1002 | ; Returns : none
|
|---|
| 1003 | ; Preserve: all registers
|
|---|
| 1004 | ; #########################################################################
|
|---|
| 1005 | DriveIO_SaveSector Proc Near Uses ax bx cx dx ds si es di
|
|---|
| 1006 |
|
|---|
| 1007 | IFDEF AUX_DEBUG
|
|---|
| 1008 | IF 0
|
|---|
| 1009 | pushf
|
|---|
| 1010 | pusha
|
|---|
| 1011 | push si
|
|---|
| 1012 | mov si, offset $+5
|
|---|
| 1013 | jmp @F
|
|---|
| 1014 | db 10,'DriveIO_SaveSector:',10,0
|
|---|
| 1015 | @@:
|
|---|
| 1016 | call AuxIO_Print
|
|---|
| 1017 | pop si
|
|---|
| 1018 | ;~ call DEBUG_DumpRegisters
|
|---|
| 1019 | ;~ call AuxIO_DumpParagraph
|
|---|
| 1020 | ;~ call AuxIO_TeletypeNL
|
|---|
| 1021 | popa
|
|---|
| 1022 | popf
|
|---|
| 1023 | ENDIF
|
|---|
| 1024 | ENDIF
|
|---|
| 1025 |
|
|---|
| 1026 | ;!
|
|---|
| 1027 | ;! DEBUG_BLOCK
|
|---|
| 1028 | ;! Force write to LBA0 to test interception routine.
|
|---|
| 1029 | ;! Do *NOT* enable unless you are debugging, will overwrite MBR !
|
|---|
| 1030 | ;!
|
|---|
| 1031 | ;~ __DIO_FORCE_LBA0_WRITE__ EQU
|
|---|
| 1032 | IFDEF AUX_DEBUG
|
|---|
| 1033 | IFDEF __DIO_FORCE_LBA0_WRITE__
|
|---|
| 1034 | xor ax,ax
|
|---|
| 1035 | xor bx,bx
|
|---|
| 1036 | xor cx,cx
|
|---|
| 1037 | inc cx
|
|---|
| 1038 | xor dh,dh
|
|---|
| 1039 | ENDIF
|
|---|
| 1040 | ENDIF
|
|---|
| 1041 |
|
|---|
| 1042 | ;
|
|---|
| 1043 | ; Check if the MBR is the destination for the write.
|
|---|
| 1044 | ; ZF=1 if so.
|
|---|
| 1045 | ;
|
|---|
| 1046 | call DriveIO_MBR_Addressed
|
|---|
| 1047 | jnz DriveIO_SaveSector_continue_write
|
|---|
| 1048 |
|
|---|
| 1049 |
|
|---|
| 1050 | ; MBR is addressed, check the sector that is requested to be written.
|
|---|
| 1051 | ; For the bootdisk it should contain the AiR-BOOT signature, valid
|
|---|
| 1052 | ; partition-table entries and the AA55h signature.
|
|---|
| 1053 | ; If not, something is terribly wrong in some piece of the AB code.
|
|---|
| 1054 | ; For any other disk (80h+) at least a valid partition table should
|
|---|
| 1055 | ; be present together with the AA55h signature.
|
|---|
| 1056 | call DriveIO_ProtectMBR
|
|---|
| 1057 | jnc DriveIO_SaveSector_continue_write
|
|---|
| 1058 |
|
|---|
| 1059 |
|
|---|
| 1060 | ;
|
|---|
| 1061 | ; WE HAVE A SEVERE ERROR CONDITION !
|
|---|
| 1062 | ; SOME AB CODE TRIES TO WRITE A NON-MBR TO THE DISK !
|
|---|
| 1063 | ; ASK THE USER TO REPORT THIS !
|
|---|
| 1064 | ; HALT THE SYSTEM !
|
|---|
| 1065 | ;
|
|---|
| 1066 |
|
|---|
| 1067 | ; Show error-box
|
|---|
| 1068 | mov cx, 0C04h
|
|---|
| 1069 | mov si, offset NonMBRwrite
|
|---|
| 1070 | call SETUP_ShowErrorBox
|
|---|
| 1071 | mov cx, 0C04h
|
|---|
| 1072 | mov si, offset NonMBRwrite_rep
|
|---|
| 1073 | call SETUP_ShowErrorBox
|
|---|
| 1074 |
|
|---|
| 1075 |
|
|---|
| 1076 | IFDEF AUX_DEBUG
|
|---|
| 1077 | pusha
|
|---|
| 1078 | mov si, offset NonMBRwrite
|
|---|
| 1079 | call AuxIO_TeletypeNL
|
|---|
| 1080 | call AuxIO_Print
|
|---|
| 1081 | call AuxIO_TeletypeNL
|
|---|
| 1082 | popa
|
|---|
| 1083 | ENDIF
|
|---|
| 1084 |
|
|---|
| 1085 | ; Show popup and halt the system.
|
|---|
| 1086 | jmp HaltSystem
|
|---|
| 1087 |
|
|---|
| 1088 |
|
|---|
| 1089 |
|
|---|
| 1090 | ;
|
|---|
| 1091 | ; Continue the write if not MBR sector or MBR to write is validated.
|
|---|
| 1092 | ;
|
|---|
| 1093 | DriveIO_SaveSector_continue_write:
|
|---|
| 1094 | test byte ptr cs:[CurIO_UseExtension], 1
|
|---|
| 1095 | jz DIOSS_UseNormal
|
|---|
| 1096 | ; Are we forced do use LBA via Setting?
|
|---|
| 1097 | ; Always use INT13X on v1.0.8+.
|
|---|
| 1098 | ;~ test byte ptr cs:[CFG_ForceLBAUsage], 1
|
|---|
| 1099 | ;~ jnz DIOSS_UseExtension
|
|---|
| 1100 | jmp DIOSS_UseExtension
|
|---|
| 1101 | ; Is the drive not a harddrive?
|
|---|
| 1102 | cmp dl, 80h
|
|---|
| 1103 | jb DIOSS_UseNormal
|
|---|
| 1104 | ; Upper 8 bits of LBA-address set? -> Use LBA (maximum boundary is FB0400h)
|
|---|
| 1105 | or bh, bh
|
|---|
| 1106 | jnz DIOSS_UseExtension
|
|---|
| 1107 | ; Compare Switch-Table value to bit 16-23 of LBA-address
|
|---|
| 1108 | mov di, dx
|
|---|
| 1109 | and di, 007Fh
|
|---|
| 1110 | cmp bptr cs:[LBASwitchTable+di], bl
|
|---|
| 1111 | jbe DIOSS_UseExtension
|
|---|
| 1112 |
|
|---|
| 1113 | DIOSS_UseNormal:
|
|---|
| 1114 |
|
|---|
| 1115 | IFDEF AUX_DEBUG
|
|---|
| 1116 | IF 0
|
|---|
| 1117 | pusha
|
|---|
| 1118 | push si
|
|---|
| 1119 | mov si, offset $+5
|
|---|
| 1120 | jmp @F
|
|---|
| 1121 | db 10,'DriveIO_WriteSectorCHS:',10,0
|
|---|
| 1122 | @@:
|
|---|
| 1123 | call AuxIO_Print
|
|---|
| 1124 | pop si
|
|---|
| 1125 | call DEBUG_DumpRegisters
|
|---|
| 1126 | call AuxIO_DumpParagraph
|
|---|
| 1127 | call AuxIO_TeletypeNL
|
|---|
| 1128 | popa
|
|---|
| 1129 | ENDIF
|
|---|
| 1130 | ENDIF
|
|---|
| 1131 |
|
|---|
| 1132 | mov di, 3 ; retry count
|
|---|
| 1133 | DIOSS_ErrorLoop:
|
|---|
| 1134 | push ds
|
|---|
| 1135 | pop es
|
|---|
| 1136 | mov bx, si ; ES:BX - Destination
|
|---|
| 1137 | mov ax, 0301h ; Function 3 - Write Sector
|
|---|
| 1138 | int 13h
|
|---|
| 1139 | jnc DIOSS_Success
|
|---|
| 1140 | dec di ; decrement retry count
|
|---|
| 1141 | jnz DIOSS_ErrorLoop
|
|---|
| 1142 | call MBR_SaveError
|
|---|
| 1143 |
|
|---|
| 1144 | DIOSS_UseExtension:
|
|---|
| 1145 |
|
|---|
| 1146 | mov di, ds ; segment for transfer address
|
|---|
| 1147 | mov cx, ax ; low word of lba
|
|---|
| 1148 | xor ax, ax ; no verify
|
|---|
| 1149 | call DriveIO_WriteSectorLBA ; extended write
|
|---|
| 1150 | jc MBR_SaveError ; halt on error
|
|---|
| 1151 |
|
|---|
| 1152 | ;~ push cx
|
|---|
| 1153 | ;~ mov cs:[INT13X_DAP_NumBlocks], 1 ; Copy ONE sector
|
|---|
| 1154 | ;~ mov wptr cs:[INT13X_DAP_Transfer+0], si
|
|---|
| 1155 | ;~ mov cx, ds
|
|---|
| 1156 | ;~ mov wptr cs:[INT13X_DAP_Transfer+2], cx ; Fill out Transfer Adress
|
|---|
| 1157 | ;~ mov wptr cs:[INT13X_DAP_Absolute+0], ax
|
|---|
| 1158 | ;~ mov wptr cs:[INT13X_DAP_Absolute+2], bx ; Fill out Absolute Sector
|
|---|
| 1159 | ;~ push cs
|
|---|
| 1160 | ;~ pop ds
|
|---|
| 1161 | ;~ mov si, offset [INT13X_DAP]
|
|---|
| 1162 | ;~ mov ax, 4300h ; Extended Write (No Verify)
|
|---|
| 1163 | ;~ int 13h
|
|---|
| 1164 | ;~ pop cx
|
|---|
| 1165 | ;~ jnc DIOSS_Success
|
|---|
| 1166 | ;~ call MBR_SaveError
|
|---|
| 1167 |
|
|---|
| 1168 | DIOSS_Success:
|
|---|
| 1169 | ret
|
|---|
| 1170 | DriveIO_SaveSector EndP
|
|---|
| 1171 |
|
|---|
| 1172 |
|
|---|
| 1173 |
|
|---|
| 1174 | ; ------------------------------------------------------
|
|---|
| 1175 | ; Rousseau: # Load the master LVM-sector if one exists #
|
|---|
| 1176 | ; ------------------------------------------------------
|
|---|
| 1177 | ; Load the master LVM-sector to get the number of sectors per track as
|
|---|
| 1178 | ; OS/2 views the drive. If no master LVM-sector is found it is assumed OS/2
|
|---|
| 1179 | ; is not installed. The master LVM-sector can be located at three different
|
|---|
| 1180 | ; places depending on drive size and partitioning scheme and driver used.
|
|---|
| 1181 | ; When DANIS506.ADD is used, the OS/2 extended geometry will be 255/127 for
|
|---|
| 1182 | ; drives >502GiB but <1TiB. Then the location will be sector 127 which
|
|---|
| 1183 | ; is LBA 126 (7Eh).
|
|---|
| 1184 | ; IBM1S506.ADD will always use 255/255 for the extended OS/2 geometry.
|
|---|
| 1185 | ; DANIS506.ADD will use 255/255 for drives >1TiB.
|
|---|
| 1186 | ; Then the location of the master LVM-sector will be 255 which is LBA 254 (FEh).
|
|---|
| 1187 | ; When OS/2 is installed on a huge drive that alread had a system on it, OS/2
|
|---|
| 1188 | ; will be confined to the lower 502GiB of the drive.
|
|---|
| 1189 | ; In this case the normal geometry from Int13X will be used.
|
|---|
| 1190 | ; This is also the case when no valid master LVM-sector can be found.
|
|---|
| 1191 | ;
|
|---|
| 1192 | ; Return CF when valid master LVM sector found, NC if not.
|
|---|
| 1193 | ; Loads sector at [LVMSector] !
|
|---|
| 1194 | DriveIO_LoadMasterLVMSector Proc Near
|
|---|
| 1195 |
|
|---|
| 1196 | IFDEF AUX_DEBUG
|
|---|
| 1197 | IF 0
|
|---|
| 1198 | pushf
|
|---|
| 1199 | pusha
|
|---|
| 1200 | push si
|
|---|
| 1201 | mov si, offset $+5
|
|---|
| 1202 | jmp @F
|
|---|
| 1203 | db 10,'DriveIO_LoadMasterLVMSector:',10,0
|
|---|
| 1204 | @@:
|
|---|
| 1205 | call AuxIO_Print
|
|---|
| 1206 | pop si
|
|---|
| 1207 | ;~ call DEBUG_DumpRegisters
|
|---|
| 1208 | ;~ call AuxIO_DumpParagraph
|
|---|
| 1209 | ;~ call AuxIO_TeletypeNL
|
|---|
| 1210 | popa
|
|---|
| 1211 | popf
|
|---|
| 1212 | ENDIF
|
|---|
| 1213 | ENDIF
|
|---|
| 1214 |
|
|---|
| 1215 | pusha
|
|---|
| 1216 |
|
|---|
| 1217 | ; Loop over the sector-translation table,
|
|---|
| 1218 | ; process the first three values from high (255) to low.
|
|---|
| 1219 | ; (bios spt, most likely 63)
|
|---|
| 1220 | mov cx,3
|
|---|
| 1221 | DriveIO_LoadMasterLVMSector_NextTry:
|
|---|
| 1222 | ; Number of sectors to read
|
|---|
| 1223 | mov [INT13X_DAP_NumBlocks],1
|
|---|
| 1224 |
|
|---|
| 1225 | ; Setup destination address
|
|---|
| 1226 | mov si, offset [LVMSector]
|
|---|
| 1227 | mov word ptr [INT13X_DAP_Transfer+0],si
|
|---|
| 1228 | mov ax, ds
|
|---|
| 1229 | mov word ptr [INT13X_DAP_Transfer+2],ax
|
|---|
| 1230 |
|
|---|
| 1231 | ; Get the sector-number of the next possible LVM sector (255,127,63)
|
|---|
| 1232 | ; using the translation table and the counter as the index
|
|---|
| 1233 | mov bx,offset [secs_per_track_table]
|
|---|
| 1234 | mov ax,cx ; 1-based index to sec_per_track_table
|
|---|
| 1235 | dec ax ; Adjust to 0-based
|
|---|
| 1236 | xlatb ; Get the (well known) SPT
|
|---|
| 1237 | dec al ; Minus 1 for LVM-record
|
|---|
| 1238 |
|
|---|
| 1239 | ;
|
|---|
| 1240 | ; AX now contains the LBA address of the sector
|
|---|
| 1241 | ; that could be an LVM sector.
|
|---|
| 1242 | ; This is all in track0 so the address will not exceed 64kiB sectors.
|
|---|
| 1243 | ;
|
|---|
| 1244 |
|
|---|
| 1245 |
|
|---|
| 1246 | IFDEF AUX_DEBUG
|
|---|
| 1247 | IF 0
|
|---|
| 1248 | pushf
|
|---|
| 1249 | pusha
|
|---|
| 1250 | push si
|
|---|
| 1251 | mov si, offset $+5
|
|---|
| 1252 | jmp @F
|
|---|
| 1253 | db 10,'geo',10,0
|
|---|
| 1254 | @@:
|
|---|
| 1255 | call AuxIO_Print
|
|---|
| 1256 | pop si
|
|---|
| 1257 | call DEBUG_DumpRegisters
|
|---|
| 1258 | call AuxIO_DumpParagraph
|
|---|
| 1259 | call AuxIO_TeletypeNL
|
|---|
| 1260 | popa
|
|---|
| 1261 | popf
|
|---|
| 1262 | ENDIF
|
|---|
| 1263 | ENDIF
|
|---|
| 1264 |
|
|---|
| 1265 |
|
|---|
| 1266 | ; Setup the requested LBA sector number
|
|---|
| 1267 | mov word ptr [INT13X_DAP_Absolute+0],ax ; LBA low NORMAL I/O GEBRUIKEN !
|
|---|
| 1268 | mov word ptr [INT13X_DAP_Absolute+2],00h ; LBA high
|
|---|
| 1269 | mov si, offset [INT13X_DAP] ; address request packet
|
|---|
| 1270 | mov ah, 42h
|
|---|
| 1271 | int 13h ; do the i/o, CF=1->error, CF=0->success
|
|---|
| 1272 |
|
|---|
| 1273 | IFDEF AUX_DEBUG
|
|---|
| 1274 | IF 0
|
|---|
| 1275 | pushf
|
|---|
| 1276 | pusha
|
|---|
| 1277 | pushf
|
|---|
| 1278 | xor ax, ax
|
|---|
| 1279 | mov al, dl
|
|---|
| 1280 | call AuxIO_TeletypeHexWord
|
|---|
| 1281 | mov al, '#'
|
|---|
| 1282 | call AuxIO_Teletype
|
|---|
| 1283 | popf
|
|---|
| 1284 | mov ax,0000h
|
|---|
| 1285 | rcl al, 1
|
|---|
| 1286 | call AuxIO_TeletypeHexWord
|
|---|
| 1287 | mov al, '#'
|
|---|
| 1288 | call AuxIO_Teletype
|
|---|
| 1289 | mov ax,word ptr [INT13X_DAP_Absolute+0]
|
|---|
| 1290 | call AuxIO_TeletypeHexWord
|
|---|
| 1291 | mov al, '#'
|
|---|
| 1292 | call AuxIO_Teletype
|
|---|
| 1293 | popa
|
|---|
| 1294 | popf
|
|---|
| 1295 | ENDIF
|
|---|
| 1296 | ENDIF
|
|---|
| 1297 |
|
|---|
| 1298 | cmc ; Complement carry so we can exit imm. on error
|
|---|
| 1299 | jnc DriveIO_LoadMasterLVMSector_End ; oops, return with NC
|
|---|
| 1300 |
|
|---|
| 1301 |
|
|---|
| 1302 | mov si,offset [LVMSector]
|
|---|
| 1303 |
|
|---|
| 1304 | ; See if this is a valid LVM-sector
|
|---|
| 1305 | ; ZF=0 if valid
|
|---|
| 1306 | call LVM_ValidateSector
|
|---|
| 1307 |
|
|---|
| 1308 | IFDEF AUX_DEBUG
|
|---|
| 1309 | IF 0
|
|---|
| 1310 | pushf
|
|---|
| 1311 | pusha
|
|---|
| 1312 | push si
|
|---|
| 1313 | mov si, offset $+5
|
|---|
| 1314 | jmp @F
|
|---|
| 1315 | db 10,'lvm record',10,0
|
|---|
| 1316 | @@:
|
|---|
| 1317 | call AuxIO_Print
|
|---|
| 1318 | pop si
|
|---|
| 1319 | call DEBUG_DumpRegisters
|
|---|
| 1320 | call AuxIO_DumpParagraph
|
|---|
| 1321 | call AuxIO_TeletypeNL
|
|---|
| 1322 | popa
|
|---|
| 1323 | popf
|
|---|
| 1324 | ENDIF
|
|---|
| 1325 | ENDIF
|
|---|
| 1326 |
|
|---|
| 1327 |
|
|---|
| 1328 | ; Yep, we found the master LVM-sector
|
|---|
| 1329 | jnz DriveIO_LoadMasterLVMSector_Found
|
|---|
| 1330 | ; Try next location
|
|---|
| 1331 | loop DriveIO_LoadMasterLVMSector_NextTry
|
|---|
| 1332 |
|
|---|
| 1333 | ; No master LVM-sector found, set CF=false
|
|---|
| 1334 | clc
|
|---|
| 1335 |
|
|---|
| 1336 | DriveIO_LoadMasterLVMSector_Found:
|
|---|
| 1337 | ; Store the address for later use.
|
|---|
| 1338 | mov ax, word ptr [INT13X_DAP_Absolute]
|
|---|
| 1339 | mov word ptr [MasterLVMLBA], ax
|
|---|
| 1340 |
|
|---|
| 1341 | DriveIO_LoadMasterLVMSector_End:
|
|---|
| 1342 | popa
|
|---|
| 1343 | ret
|
|---|
| 1344 | DriveIO_LoadMasterLVMSector Endp
|
|---|
| 1345 |
|
|---|
| 1346 |
|
|---|
| 1347 |
|
|---|
| 1348 |
|
|---|
| 1349 | ; ---------------------------------------------------
|
|---|
| 1350 | ; Rousseau ## Large drives, (OS/2) geometry and LBA ##
|
|---|
| 1351 | ; ---------------------------------------------------
|
|---|
| 1352 | ; A sector size of 512 bytes is assumed in the below calculations.
|
|---|
| 1353 | ; Note that this scheme changes when the sector size will be 4096 or larger,
|
|---|
| 1354 | ; like with modern drives that do not translate to 512 bytes per sector anymore.
|
|---|
| 1355 | ; These drives will have a capacity above the 2TiB LBA32 boundary.
|
|---|
| 1356 | ; For now, we assume drives <=2TiB with a sector size of 512 bytes.
|
|---|
| 1357 |
|
|---|
| 1358 | ; There are a few boundaries that are of importance.
|
|---|
| 1359 | ; Note that these are disk-boundaries and not partition boundaries.
|
|---|
| 1360 | ; Even with a small partition, like <502GiB, OS/2 will use extended geometry on
|
|---|
| 1361 | ; an empty huge disk.
|
|---|
| 1362 | ; These boundaries are (from high to low):
|
|---|
| 1363 |
|
|---|
| 1364 | ; (code 5)
|
|---|
| 1365 | ; 2^32 = 4294967296 = 100000000 sectors = 2048 GiB
|
|---|
| 1366 | ; This is the LBA32 2TiB boundary.
|
|---|
| 1367 | ; Everything above it must be addressed using LBA48.
|
|---|
| 1368 | ; OS/2 can currently not address this space above.
|
|---|
| 1369 |
|
|---|
| 1370 | ; (code4)
|
|---|
| 1371 | ; 65536*255*255 = 4261478400 = FE010000 sectors ~ 2032 GiB
|
|---|
| 1372 | ; This is the max OS/2 boundary using 255/255 extended geometry.
|
|---|
| 1373 | ; OS/2 can currently not address this space above.
|
|---|
| 1374 |
|
|---|
| 1375 | ; (code 3)
|
|---|
| 1376 | ; 2^31 = 2147483648 = 80000000 sectors = 1024 GiB
|
|---|
| 1377 | ; This is the LBA32 1TiB boundary.
|
|---|
| 1378 | ; OS/2 can address this space and will use 255/255 extended geometry.
|
|---|
| 1379 |
|
|---|
| 1380 | ; (code 2)
|
|---|
| 1381 | ; 65536*255*127 = 2122383360 = 7E810000 sectors ~ 1012 GiB
|
|---|
| 1382 | ; This is the DANI 1TiB boundary.
|
|---|
| 1383 | ; OS/2 can address this space and will use 255/255 extended geometry.
|
|---|
| 1384 | ; Below this DANI will use 255/127 extended geometry.
|
|---|
| 1385 | ; This matters on where the LVM-sectors are located !
|
|---|
| 1386 |
|
|---|
| 1387 | ; (code 1)
|
|---|
| 1388 | ; 65536*255*63 = 1052835840 = 3EC10000 sectors ~ 502 GiB
|
|---|
| 1389 | ; This is the current OS/2 limit using this geometry because OS/2 can
|
|---|
| 1390 | ; currently not address more than 65536 cylinders.
|
|---|
| 1391 | ; DANI will address space above with 255/127 extended geometry up until
|
|---|
| 1392 | ; the DANI 1TiB boundary (code 2)
|
|---|
| 1393 |
|
|---|
| 1394 | ; (code 0)
|
|---|
| 1395 | ; Everything below 65536*255*63 will be addressed using standard geometry.
|
|---|
| 1396 |
|
|---|
| 1397 |
|
|---|
| 1398 | ;
|
|---|
| 1399 | ; This function will return the following values:
|
|---|
| 1400 | ;
|
|---|
| 1401 |
|
|---|
| 1402 | ; 5 = This drive is above the 2^32 LBA32 (2TB) boundary and has more
|
|---|
| 1403 | ; than 4294967296 sectors.
|
|---|
| 1404 | ; LBA48 addressing is needed to access the complete capacity of the drive.
|
|---|
| 1405 | ; OS/2 is currently unable to do so.
|
|---|
| 1406 |
|
|---|
| 1407 | ; 4 = This drive is above the 65536*255*255 (4261478400) boundary but below 2^32.
|
|---|
| 1408 | ; This is an OS/2 boundary and OS/2 is not able to access the drive above
|
|---|
| 1409 | ; this boundary.
|
|---|
| 1410 |
|
|---|
| 1411 | ; 3 = This drive is above the 2^31 (1TB) boundary and has more than
|
|---|
| 1412 | ; 2147483648 sectors.
|
|---|
| 1413 | ; OS/2 is able to access the drive using it's extended geometry.
|
|---|
| 1414 | ; Both DANIS506 and IBM1S506 will use the 255/255 scheme.
|
|---|
| 1415 |
|
|---|
| 1416 | ; 2 = This drive is above the 65536*255*127 (2122383360) boundary but below 2^31.
|
|---|
| 1417 | ; OS/2 is able to access the drive using it's extended geometry.
|
|---|
| 1418 | ; Both DANIS506 and IBM1S506 will use the 255/255 scheme.
|
|---|
| 1419 |
|
|---|
| 1420 | ; 1 = This drive is above the 65536*255*63 (1052835840) boundary but
|
|---|
| 1421 | ; below 65536*255*127.
|
|---|
| 1422 | ; OS/2 is able to access the drive using it's extended geometry.
|
|---|
| 1423 | ; Note that DANIS506 will use 255/127 and IBM1S506 will use 255/255 geometry !
|
|---|
| 1424 | ; Using DANI or IBM influences the location of the LVM info-sectors !
|
|---|
| 1425 |
|
|---|
| 1426 | ; 0 = This drive is below the 65536*255*63 (1052835840) boundary.
|
|---|
| 1427 | ; OS/2 is able to access this drive using the standard 255/63 geometry.
|
|---|
| 1428 |
|
|---|
| 1429 | ; So, any return value >0 means OS/2 extended geometry will be used.
|
|---|
| 1430 | ; Value 1 will use 255/127 with DANIS506 but 255/255 with IBM1S506.
|
|---|
| 1431 | ; Values 2 and 3 will use 255/255 on both drivers.
|
|---|
| 1432 | ; You can or with 0x01 and check for 3 in this case.
|
|---|
| 1433 | ; Any value above 3 will be a drive who's capacity cannot be fully used by OS/2
|
|---|
| 1434 | ; The upper limit of 65536*255*255 will be in effect here.
|
|---|
| 1435 |
|
|---|
| 1436 | ; Note this function currently handles the boot-drive only !
|
|---|
| 1437 | ; It should be extended and use dl for the drive-number as a parameter.
|
|---|
| 1438 | ; Because we use this function to get this info in a number of places,
|
|---|
| 1439 | ; all regs and flags except AX are saved and restored.
|
|---|
| 1440 |
|
|---|
| 1441 | ; DL contains BIOS disk-number; 80h for first, 81h for second, etc.
|
|---|
| 1442 | DriveIO_GatherDiskInfo Proc Near
|
|---|
| 1443 |
|
|---|
| 1444 | IFDEF AUX_DEBUG
|
|---|
| 1445 | IF 0
|
|---|
| 1446 | pushf
|
|---|
| 1447 | pusha
|
|---|
| 1448 | push si
|
|---|
| 1449 | mov si, offset $+5
|
|---|
| 1450 | jmp @F
|
|---|
| 1451 | db 10,'DriveIO_GatherDiskInfo:',10,0
|
|---|
| 1452 | @@:
|
|---|
| 1453 | call AuxIO_Print
|
|---|
| 1454 | pop si
|
|---|
| 1455 | ;~ call DEBUG_DumpRegisters
|
|---|
| 1456 | ;~ call AuxIO_DumpParagraph
|
|---|
| 1457 | ;~ call AuxIO_TeletypeNL
|
|---|
| 1458 | popa
|
|---|
| 1459 | popf
|
|---|
| 1460 | ENDIF
|
|---|
| 1461 | ENDIF
|
|---|
| 1462 |
|
|---|
| 1463 | pushf
|
|---|
| 1464 | push bx
|
|---|
| 1465 | push cx
|
|---|
| 1466 | push dx
|
|---|
| 1467 | push si
|
|---|
| 1468 | push di
|
|---|
| 1469 | push es
|
|---|
| 1470 |
|
|---|
| 1471 | ; Set ES to CS for buffer clearing
|
|---|
| 1472 | push cs
|
|---|
| 1473 | pop es
|
|---|
| 1474 |
|
|---|
| 1475 | ; Clear the buffer
|
|---|
| 1476 | ; Also setup the buffer size.
|
|---|
| 1477 | ; Old Phoenix BIOSses require word (flags) at 02 to be zero,
|
|---|
| 1478 | ; so we clear the whole buffer to be sure.
|
|---|
| 1479 | mov cx, i13xbuf_size ; Dynamically calculated by assembler.
|
|---|
| 1480 | mov di, offset i13xbuf ; Points to size field.
|
|---|
| 1481 | mov [di],cx ; Setup buffer-size.
|
|---|
| 1482 | inc di
|
|---|
| 1483 | inc di ; Now pointing at actual buffer.
|
|---|
| 1484 | xor ah,ah ; Fill value.
|
|---|
| 1485 | cld ; Direction up.
|
|---|
| 1486 | rep stosb ; Clear buffer.
|
|---|
| 1487 |
|
|---|
| 1488 | ; Get the drive parameters
|
|---|
| 1489 | mov ah, 48h ; Get Drive Parameters (extended version)
|
|---|
| 1490 | ;mov dl, 80h ; Drive number
|
|---|
| 1491 | mov si, offset i13xbuf ; Buffer for result-info
|
|---|
| 1492 | push dx
|
|---|
| 1493 | int 13h ; Call the BIOS-function
|
|---|
| 1494 | pop dx
|
|---|
| 1495 |
|
|---|
| 1496 | ; Do some error-checking
|
|---|
| 1497 | or ah,ah ; AH is zero if no error (ZF=1 if no error)
|
|---|
| 1498 | mov ax,0 ; Setup code for non-huge drive (does not influence ZF)
|
|---|
| 1499 | jz DriveIO_GatherDiskInfo_ok ; Return if error (AL<>0 thus ZF=0) but CY not set, assuming non-huge drive
|
|---|
| 1500 | jnc DriveIO_GatherDiskInfo_ok ; Return if error (CY=1), assuming non-huge drive
|
|---|
| 1501 | jmp DriveIO_GatherDiskInfo_ret
|
|---|
| 1502 |
|
|---|
| 1503 |
|
|---|
| 1504 | DriveIO_GatherDiskInfo_ok:
|
|---|
| 1505 |
|
|---|
| 1506 | ;
|
|---|
| 1507 | ; Store the drive geometry
|
|---|
| 1508 | ;
|
|---|
| 1509 |
|
|---|
| 1510 | mov si, offset i13xbuf
|
|---|
| 1511 |
|
|---|
| 1512 | xor dh,dh
|
|---|
| 1513 | and dl,01111111b
|
|---|
| 1514 | shl dx,1
|
|---|
| 1515 | shl dx,1
|
|---|
| 1516 |
|
|---|
| 1517 | ; Store number of cylinders on disk
|
|---|
| 1518 | mov bx, offset BIOS_Cyls
|
|---|
| 1519 | add bx,dx
|
|---|
| 1520 | mov ax,[si+04h]
|
|---|
| 1521 |
|
|---|
| 1522 | mov word ptr [bx+00],ax
|
|---|
| 1523 | mov ax,[si+06]
|
|---|
| 1524 | mov word ptr [bx+02],ax
|
|---|
| 1525 |
|
|---|
| 1526 | ; Store number of heads per cylinder
|
|---|
| 1527 | mov bx, offset BIOS_Heads
|
|---|
| 1528 | add bx,dx
|
|---|
| 1529 | mov ax,[si+08h]
|
|---|
| 1530 | mov word ptr [bx+00],ax
|
|---|
| 1531 | mov ax,[si+0ah]
|
|---|
| 1532 | mov word ptr [bx+02],ax
|
|---|
| 1533 |
|
|---|
| 1534 | ; Store number of sectors per track
|
|---|
| 1535 | mov bx, offset BIOS_Secs
|
|---|
| 1536 | add bx,dx
|
|---|
| 1537 | mov ax,[si+0ch]
|
|---|
| 1538 | mov word ptr [bx+00],ax
|
|---|
| 1539 |
|
|---|
| 1540 | ; Update first byte of translation-table to conform to BIOS SPT
|
|---|
| 1541 | mov byte ptr [secs_per_track_table], al
|
|---|
| 1542 |
|
|---|
| 1543 | mov ax,[si+0eh]
|
|---|
| 1544 | mov word ptr [bx+02],ax
|
|---|
| 1545 |
|
|---|
| 1546 | ; Store total secs
|
|---|
| 1547 | mov bx, offset BIOS_TotalSecs
|
|---|
| 1548 | add bx,dx
|
|---|
| 1549 | add bx,dx
|
|---|
| 1550 | mov ax,[si+10h]
|
|---|
| 1551 |
|
|---|
| 1552 | mov word ptr [bx+00],ax
|
|---|
| 1553 | mov ax,[si+12h]
|
|---|
| 1554 | mov word ptr [bx+02],ax
|
|---|
| 1555 | mov ax,[si+14h]
|
|---|
| 1556 | mov word ptr [bx+04],ax
|
|---|
| 1557 | mov ax,[si+18h]
|
|---|
| 1558 | mov word ptr [bx+06],ax
|
|---|
| 1559 |
|
|---|
| 1560 | ; Store number of bytes per sector
|
|---|
| 1561 | mov bx, offset BIOS_Bytes
|
|---|
| 1562 | add bx,dx
|
|---|
| 1563 | mov ax,[si+18h]
|
|---|
| 1564 | mov [bx],ax
|
|---|
| 1565 |
|
|---|
| 1566 |
|
|---|
| 1567 | ;
|
|---|
| 1568 | ; See of it's a huge drive of not
|
|---|
| 1569 | ;
|
|---|
| 1570 |
|
|---|
| 1571 | ; Drive is larger than 2TiB
|
|---|
| 1572 | mov ax,5 ; Drive code (5)
|
|---|
| 1573 | mov bx, [si+14h] ; Low word of high dword of sector-count
|
|---|
| 1574 | or bx, [si+16h] ; High word of high dword of sector-count
|
|---|
| 1575 | jnz DriveIO_GatherDiskInfo_ret ; If non-zero we have a drive with >2^32 sectors and thus LBA48 addressing
|
|---|
| 1576 |
|
|---|
| 1577 | ; Drive is larger than max OS/2 capacity
|
|---|
| 1578 | dec ax ; Drive code (4)
|
|---|
| 1579 | mov bx, [si+12h] ; High word of low dword of sector-count
|
|---|
| 1580 | cmp bx, 0fe01h ; Boundary
|
|---|
| 1581 | jae DriveIO_GatherDiskInfo_ret ; If above or equal to boundary,
|
|---|
| 1582 | ; we have a drive larger than to 65536*255*255 = FE010000 sectors
|
|---|
| 1583 |
|
|---|
| 1584 | ; Drive can be completely utilized by OS/2
|
|---|
| 1585 | dec ax ; Drive code (3)
|
|---|
| 1586 | cmp bx, 8000h ; Boundary
|
|---|
| 1587 | jae DriveIO_GatherDiskInfo_ret ; If above or equal to boundary,
|
|---|
| 1588 | ; we have a drive larger than 2^31 sectors but smaller than 65536*255*255
|
|---|
| 1589 |
|
|---|
| 1590 | ; This is the small area between DANI 1TiB and LBA 1TiB
|
|---|
| 1591 | dec ax ; Drive code (2)
|
|---|
| 1592 | cmp bx, 7e81h ; Boundary
|
|---|
| 1593 | jae DriveIO_GatherDiskInfo_ret ; If above or equal to boundary,
|
|---|
| 1594 | ; we have a drive larger than 65536*255*127 but <65536*255*255
|
|---|
| 1595 | ; DANIS506.ADD will use 255/255 extended geometry
|
|---|
| 1596 |
|
|---|
| 1597 | ; DANI will use 255/127 in this area, this could impact the location of LVM-sectors ! (last sec on track)
|
|---|
| 1598 | dec ax ; Drive code (1)
|
|---|
| 1599 | cmp bx, 3ec1h ; Boundary
|
|---|
| 1600 | jae DriveIO_GatherDiskInfo_ret ; If above or equal to boundary,
|
|---|
| 1601 | ; we have a drive larger than 65536*255*63 sectors (OS/2 502GiB Limit!)
|
|---|
| 1602 | ; DANIS506.ADD will use 255/127 extended geometry !
|
|---|
| 1603 | ; IBM1S506.ADD will use 255/255 extended geometry !
|
|---|
| 1604 |
|
|---|
| 1605 | ; We have a drive that can be addressed using standard 255/63 geometry
|
|---|
| 1606 | dec ax ; Drive code (0)
|
|---|
| 1607 | ; We have a drive smaller than 65536*255*63 = 3EC10000 sectors
|
|---|
| 1608 |
|
|---|
| 1609 | DriveIO_GatherDiskInfo_ret:
|
|---|
| 1610 | pop es
|
|---|
| 1611 | pop di
|
|---|
| 1612 | pop si
|
|---|
| 1613 | pop dx
|
|---|
| 1614 | pop cx
|
|---|
| 1615 | pop bx
|
|---|
| 1616 |
|
|---|
| 1617 | mov byte ptr [CurIO_UseExtension],1
|
|---|
| 1618 |
|
|---|
| 1619 | popf
|
|---|
| 1620 | ret
|
|---|
| 1621 | DriveIO_GatherDiskInfo EndP
|
|---|
| 1622 |
|
|---|
| 1623 |
|
|---|
| 1624 |
|
|---|
| 1625 | ; Values for sectors per track table corresponding to DriveIO_IsHugeDrive return value.
|
|---|
| 1626 | secs_per_track_table db 63,127,255,255,255,255
|
|---|
| 1627 |
|
|---|
| 1628 | db_lmlvm db 'Load Master LVM -- disk: ',0
|
|---|
