Question 1. Resistive Circuit a. For the circuit shown in Figure 1 indicate the magnitude and direction of the current that flows through the 24V constant voltage source assuming R = 20. b. Show the power value for each component in the circuit in accordance with the passive sign convention R 402 ww 24V 10 Ω ww www 10 Ω 4Ω 40 w Figure 1: A resistor network. 12

Question 1. Resistive Circuit a. For the circuit shown in Figure 1 indicate the magnitude and direction of the current that flows through the 24V constant voltage source assuming R = 20. b. Show the power value for each component in the circuit in accordance with the passive sign convention R 402 ww 24V 10 Ω ww www 10 Ω 4Ω 40 w Figure 1: A resistor network. 12

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 9RQ: What is the power factor of the circuit in Question 6?

See similar textbooks

Similar questions

What is the power factor of the circuit in Question 6?
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive circuit?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
True or False: Ohms law applies to all types of electrical circuits.
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
The hot water for the heating system for a small factory is supplied by a single boiler. The bolier is locatd in a small building separate form the factory. The power supplied to the bioler is 240-volt single-phase without a netural conductor. At the present time, the small building housing the bioler has no inside lighting. The business owner desires that four 100-watt lamps be installed inside the building. All lamps are to be connected to a single switch. The lamps are to be connected to the present 240-volt sercvice inside the building. How would you accomplish this task? Explain your answer.
It is decided to use parallel 0000 conductors to supply the load in Question 11. How many 0000 conductors will be needed?
If the frequency in Question 8 is reduced to 50 Hz, how much current will flow in the circuit?
Schematic diagrams break the wiring of control systems down into a(n) _____ arrangement. a. circuit-by-circuit b. series circuit c. individual circuit d. none of the above
Refer to the formulas in Appendix B in the Resistive-Capacitive Parallel Circuits section. A resistor and capacitor are connected in parallel to a 208-V, 60-Hz power source. An ammeter indicates a total circuit current of 46 amps, and a wattmeter indicates a true power of 4975 W. What is the resistance of the circuit?
An R-L series circuit contains two resistors and two inductors. The resistors are 68 and 124 . The inductors have inductive reactances of 44 and 225 . The total voltage is 240 volts. Find the voltage drop across the 124- resistor.