Problem 1 (50 pt.) Find V in the circuit below using Thevenin's/Norton's theorem. 5 V 2 k ww 1 k 1 kf w ww 21. 3 mA 2 k 3 k V. Problem 2 (25 pt.) Figure 1: Circuit for Problem 1 Find I, using source transformation in the circuit below. 4k 10 V ww 1 kn ww 3 mA 2 k 3 k 2 k 2 kn Figure 2: Circuit for Problem 2

Problem 1 (50 pt.) Find V in the circuit below using Thevenin's/Norton's theorem. 5 V 2 k ww 1 k 1 kf w ww 21. 3 mA 2 k 3 k V. Problem 2 (25 pt.) Figure 1: Circuit for Problem 1 Find I, using source transformation in the circuit below. 4k 10 V ww 1 kn ww 3 mA 2 k 3 k 2 k 2 kn Figure 2: Circuit for Problem 2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 12PP: In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.

See similar textbooks

Similar questions

In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.
An AC electric motor is connected to a 240-V, 60-Hz source. A clamp-on ammeter with a peak hold function reveals that the motor has an inrush current of 34 A when the motor is first started. Your job is to reduce the inrush current to a value of 20 A by connecting a resistor in series with the motor. The resistor will be shunted out of the circuit after the motor is started. Using an ohmmeter, you find that the motor has a wire resistance of 3 . How much resistance should be connected in series with the motor to reduce the starting current to 20 A?
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
Schematic diagrams break the wiring of control systems down into a(n) _____ arrangement. a. circuit-by-circuit b. series circuit c. individual circuit d. none of the above
You are an electrician on the job. The electrical blueprint shows that eight 500-W lamps are to be installed on the same circuit. The circuit voltage is 277 V and is protected by a 20-A circuit breaker. A continuous-use circuit can be loaded to only 80% of its rating. Is a 20-A circuit large enough to carry this load?
An ac resistance is higher than a dc resistance. True False
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor domain.
Given the complex numbers A1=630 and A2=4+j5, (a) convert A1 to rectangular form: (b) convert A2 to polar and exponential form: (c) calculate A3=(A1+A2), giving your answer in polar form: (d) calculate A4=A1A2, giving your answer in rectangular form: (e) calculate A5=A1/(A2*) giving your answer in exponential form.
3. What is power factor?